541374
32
Zoom out
Zoom in
Previous page
1/34
Next page
32 WZ
3
16:2 and 12:2 User Guide
AUX master balance option The 6 aux
outputs are impedance balanced as standard
operating at nominal -2dBu and with +21dBu
maximum drive. They provide similar interference
rejection to electronically balanced outputs when
connected to balanced equipment inputs. An
electronically balanced option is available if you
require nominal +4dBu and higher output drive up to
+26dBu over very long cable runs. However, it is not
usually necessary to fit this option as the impedance
balanced drive satisfies most applications. Check
that you really need the option before fitting it.
There are two balanced driver ICs which may be
used. Either is suitable. These are available from
Allen & Heath or most electronic component
suppliers. The Allen & Heath part number is shown
below:
SSM2142P A&H Part AE0302
DRV134 A&H Part AE5725
For each aux master, snip the legs of the two zero
ohm resistor links as shown. This removes them
from the circuit. Now simply plug the option IC into
the socket. Observe the correct IC pin1 orientation
and make sure its legs are correctly aligned with the
socket. Test the output once the work is complete.
You should measure the same level but opposite
polarity signal between + (hot) and ground, and –
(cold) and ground.
Sys-Link II output option A blank plate is
fitted here as standard. This may be replaced with
an optional card which provides a 37way D
connector for linking the outputs to other Allen &
Heath consoles already fitted with Sys-Link II. The
WZ
3
12:2 or WZ
3
16:2 can become input channel
expanders for other consoles.
IMPORTANT: The option does not include the Sys-
Link II input. Therefore the WZ
3
12:2 or WZ
3
16:2
cannot be used as the master in a linked system, nor
can two of these models be linked together. You
need to connect these to a console that does include
the Sys-Link II input connection, for example the
WZ
3
14:4:2 or ML3000 with the option already fitted.
Also note that you need an adapter cable if you are
connecting Sys-Link II (Version 2) to the older Sys-
Link I (Version 1) standard.
A 37way shielded multi-core cable carries the
MixWizard balanced mix signals and PFL system to
the master console.
For full details please refer to the Sys-Link option
Applications Note AP5736 and Fitting Instructions
AP5735.
AUX MASTER - BALANCED OUTPUT OPTION
U12 U11 U10 U9 U8 U7
AUX6 AUX5 AUX4 AUX3 AUX2 AUX1
CUT OUT 2x 0 OHM RESISTOR LINKS
PLUG IN SSM2142 or DRV134 IC
1
SYS-LINK II OUTPUT
WZ312:2 OR WZ316:2
SYS-LINK II INPUT
WZ314:4:2 OR OTHER A&H CONSOLE
SYS-LINK II OUTPUT
MASTER CONSOLE
37WAY CABLE
SLAVE CONSOLE
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath MixWizard WZ3-12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath MixWizard WZ3-12 in the language / languages: English as an attachment in your email.

The manual is 4,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Allen-Heath MixWizard WZ3-12

Allen-Heath MixWizard WZ3-12 User Manual - German - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info