541374
30
Zoom out
Zoom in
Previous page
1/34
Next page
30 WZ
3
16:2 and 12:2 User Guide
REMOVE SIDE TRIMS
REMOVE M4 POZI SCREW PER SIDE
ROTATE POD
REMOVE 4x M3 TORX SCREWS
REMOVE 4x M4 POZI SCREWS PER SIDE
REMOVE 3x M3 TORX SCREWS
ROTATE POD
LIFT OFF BASE
MONO INPUT STEREO INPUT (12:2)
AUX MASTER MASTER LR
DIRECT OUT PRE/POST FADER
AUX PRE/POST INSERT/EQ
AUX PRE/POST FADER
AUX PRE/POST FADER
AUX STEREO/MONO
AUX BALANCE OPTION
ST AUX STEREO/MONO
AB PRE/POST LR FADER
User Options
The MixWizard has a versatile architecture which
should satisfy most applications you may encounter
without modification. However, the following internal
options provide alternative settings for those
applications that may demand them. Access is
required to the internal assemblies. For user
convenience, pluggable jumper links are used in
most places.
Remove the base Start by removing the side
trims if fitted using a Pozi crosshead screwdriver.
Release the two M4 Pozi head pod securing screws
and rotate the connector pod to gain access to the
three M3 rear base fixing screws. Use a Torx
starhead screwdriver to remove these. Rotate the
pod again to remove the four M3 underside base
screws using the Torx driver. Carefully lift off the
base.
Configure the internal options Fit the
options required. Set the option jumpers to the
required positions. Make sure they are pressed fully
home. Check that all channels are correctly set and
all options fitted according to their instructions. Make
sure that no debris or parts are left loose inside the
console.
Refit the base Carefully reposition the base.
Refit the fixing screws. Lock the connector pod in
the required position using the securing screws.
Refit the side trims if required.
IMPORTANT: Check carefully that all channel
jumpers are correctly set as required. Errors on one
or more channels now may cause user problems
later. We recommend that you write the repositioned
jumper settings on a label and adhere this to the rear
panel. This would provide a helpful reference to
other users of the console.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath MixWizard WZ3-12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath MixWizard WZ3-12 in the language / languages: English as an attachment in your email.

The manual is 4,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Allen-Heath MixWizard WZ3-12

Allen-Heath MixWizard WZ3-12 User Manual - German - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info