551733
5
Zoom out
Zoom in
Previous page
1/11
Next page
AEG installation manual
5
Inlet Hole
Make a hole in the board material for the inlet valve as shown in the fi gure.
The size of the rectangular opening should be 2 3/8” x 4 3/4” (60mm x
110mm). In existing houses where tubes are routed underneath, a hole can
be drilled for the tube using a guide hole as a template. Glue the 90° inlet
elbow onto the sleeve of the mounting bracket. Leave a gap of approxi-
mately 5/8” (15cm) for the low-voltage cable to be connected to the inlet
valve. Then the dust tube is glued into the inlet elbow.
Strip off approximately 1” (2cm to 3cm) of the insulation from the end
of the low-voltage cable. Roll the end of the cable two turns around the
screws in the inlet valve and tighten the screws.
Screw the inlet valve into the mounting bracket and make sure that the
screw does not extend through the tube. If necessary, use shorter screws.
In a complete wall structure, the mounting bracket is held in place by a
hook as shown in the fi gure.
Installation in a Brick or Concrete Wall
When installing the inlet valve, sink the pipes, the inlet elbow, and the
mounting bracket in the wall so that the highest surface of the mounting
bracket is approximately 1/4” (5mm) deeper than the fi nal inner surface.
For the tubing system, make a 3 1/8” x 3 1/8” (80mm x 80mm) channel
in the brick or concrete wall independent of the fi nal thickness of the wall.
The tubing installation must be sturdy enough so that tubes and parts
do not move out of their positions later during the installation work. It is
recommended to cover the opening of the inlet valve to protect it from cast
material.
nished wall surface
wall mounting
bracket
3 1/8” (80 mm)
pipe
90° elbow
low voltage
cable
Thread the low voltage cable through the slot
in the mounting bracket
mounting
bracket
min. 5/8” (15 cm)
wall
The tube can also be installed block / brick
wall with the rear side. In this case, the wall
is made imurasiaa for a picture with the hole.
2 3/8”
(60 mm)
4 3/4”
(110 mm)
2 3/8” (
60 mm)
4 3/4” (110 mm)
2 1/4”-2 1/2”
(57–62 mm)
Do not disconnect the mounting screws
completely. Loosen them enough to fi t
the low voltage cable around them and
then tighten.
long screw
short screw
inlet vavle
mounting bracket
low voltage cable
90° elbow
pipe
hook
wall
fi n i
s
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG Oxygen - K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG Oxygen - K in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG Oxygen - K

AEG Oxygen - K User Manual - English, German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info