Manual ZTE MF-80 (page 1 of 2) (English)

596004

Zoom out

Zoom in

1/2

ZTE CORPORATION

NO. 55, Hi-tech Road South, ShenZhen, P.R.China

Postcode: 518057 Tel: +86-755-26779999

URL: http://www.zte.com.cn E-mail: mobile@zte.com.cn

ZTE MF80

Quick Guide

Operate system

Windows 7, Windows Vista(32bit or 64bit),

Windows XP (SP2 or later), MAC (10.4 or later)

Web Browser

IE (7.0 or later), Firefox (2.0 or later), Opera (10.0

or later), Safari (4.0 or later), Chrome (5.0 or

later)

Operating temperature 0°C ~ +40°C

Storage temperature -20°C ~ +50°C

Charging temperature 0°C ~ +45°C

Humidity 5%~ 95%

Notes: microSD

is a trademark of SD Card Association.

The device’s standby and working time are only for your reference, and

based on ideal working environment.

Getting to Know Your Device

The following gure shows the appearance of the device, it is only for your

reference. The actual device may be different.

Right Side Front Left Side

Interface and Buttons

1. External Antenna

Connector

It is used to connect an external antenna to enhance

the signal strength.

2. Power Hold the Power button to switch on/off the device.

3. Connect

• Press it to connect to the Internet or disconnect

from the Internet.

• Hold it for more than 3 seconds to switch the

WAN Connection Mode between A(Always on) or

M(Manual).

4. WPS

This button is used to start/end Wi-Fi Protected Setup

authentication process and enable/disable the Wi-Fi

function.

• Hold it for more than 3 seconds to activate the WPS

function.

• Press it to enable/disable Wi-Fi function.

5. LED Screen

It indicates the signal type, signal strength, battery, Wi-

Fi, etc.

6. Memory card slot

(microSD card)

It is where you insert the memory card (microSD card).

7. Charger/USB

port

• Charge your device.

• Connect the client to your device via USB cable.

Notes:

Hold the WPS and Power buttons simultaneously until the LED screen turns

off, and then release the buttons. The device will restart automatically and

restore to the factory default settings.

LED Indicator

When the device is powered on, the following icons will appear on the LED

screen, with the corresponding indicates listed in the table below:

Icon Indication

Network signal strength.

Network type. 2G or 3G icon will appear on the LED

screen according to the network being connected.

Connect to the Internet automatically.

Connect to the Internet manually.

Roaming network indication.

New message received.

Wi-Fi Status and number of the connecting users.

Battery power indication.

Hardware Installation

Inserting SIM Card and Battery

1. Slide the battery cover, and remove it.

2. Insert the SIM card into the SIM card holder.

3. Insert the battery as shown with the contacts located against the metal

springs, and press the battery down into the case.

4. Put the battery cover of the modem atly upon the body of device. Direct

the battery cover towards the locking catches on the sides of the device,

and then push the battery cover to lock the cover into its place.

Inserting microSD Card

1. Pull the microSD cover out of the card slot.

Notes:

Do not pull the cover rudely, as it is connected with the device.

2. Insert the microSD card into the microSD slot. The following picture

shows the correct inserting direction. You will hear a click when the

microSD card locks in place.

3. Close the microSD cover.

Switching On/Off Your Device

Hold the Power button to switch on/off the device.

Notes:

The device is powered on when the LED screen lights up.

Charging Your Device

You can charge your device by using USB cable or adapter.

1. Insert the charger lead carefully with the plug arrow facing the bottom of

the device.

2. The plug only ts one way. Do not use excessive force to insert the plug.

3. Make sure the plug is the right way round and lined up correctly and

insert it gently.

Working Mode

Your device supports three working modes. For the client, we only use PC or

laptop as the example in this document.

USB Mode: Connect to the device with the USB cable.

Wi-Fi Mode: Connect to the device via Wi-Fi.

Mixed Mode: Connect to the device with the above two connection methods.

Notes:

If you want to connect to the Internet by using Wi-Fi mode, make sure that

the client supports the Wi-Fi function.

The following picture is the application example. All of the client devices can

surf on the Internet at the same time.

LEGAL INFORMATION

No part of this publication may be excerpted, reproduced, translated or utilized in

any form or by any means, electronic or mechanical, including photocopying and

microlm, without the prior written permission of ZTE Corporation.

The manual is published by ZTE Corporation. We reserve the right to make

modications on print errors or update specications without prior notice.

Version No. : R1.0

Establish a connection between your device and

the client

Via USB Cable

1. Connect your device and the client with the USB cable.

2. Power on your device.

3. Follow the system prompts to complete the software installation.

Notes:

• If the system does not launch installation automatically, you can run the

installation program in path of My Computer > Mobile Hotspot.

• The driver of your device will be installed at the same time.

4. After the installation, the system will create a shortcut icon on your

desktop and a program group in the Start→Programs menu. The

connection between your device and the client will be established

successfully a moment later.

Via Wi-Fi

1. Power on your device directly. It will take 1~2 minutes to initialize.

2. Use your normal Wi-Fi application on the client to search the available

wireless network.

Notes:

You need to check your Wireless Network Connection. Set the client

to obtain an IP address automatically in the Internet protocol (TCP/IP)

properties, and the client will get an IP address like “192.168.0.100”.

3. Select the SSID of your device, and then click Connect.

Introduction

ZTE MF80 is a 3G/2G mobile hotspot device, working in GSM/GPRS/

EDGE/WCDMA/HSPA/HSPA+ network. The client devices could connect to

it via USB or Wi-Fi interface. The device supports data and SMS services,

enabling you to communicate anytime and anywhere.

This quick guide provides instructions on how to install and get started with

the product. For information about connection of services, please consult

your service provider.

Specication

Data Service

HSPA+: DL 42Mbps

HSUPA: UL 5.76Mbps

WCDMA CS: 64kbps UL/DL

WCDMA PS: 384kbps UL/DL

Interface USB and Wi-Fi

Wi-Fi Standard 802.11b/g

Wi-Fi Security WEP/WPA/WPA2

USB Version USB 2.0 HIGH SPEED

USB Interface Type Micro USB

Weight 97g

Dimensions (W×H×D): 102mm*53mm*16.6mm

microSD card Support up to 32GB microSD card

Power Adapter 5V/1.5A

Battery 1900mAh

*Standby time 100hours

*Working time 4.5hours

1 2 3 4 5 6 7 8 9

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ZTE MF-80 in the language / languages: English as an attachment in your email.

The manual is 2,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ZTE MF-80 Manual

Product: