666303
25
Zoom out
Zoom in
Previous page
1/28
Next page
ZOOM RFX-2200
25
Preset programs
528
(8 effects x 6 banks x 11
variations)
Program memory
100
Sampling frequency
44.1 kHz
A/D converter
20 bit, 64 times oversampling
D/A converter
20 bit, 128 times oversampling
Inputs
Line input
2 x standard mono phone jack
Input impedance
10 kiloohms (mono),
20 kiloohms (stereo)
Reference input level
-10 to +4 dBm
Microphone input
XLR-3-31/standard phone
combo jack
(Balanced operation)
Input impedance 4.5 kilohm,
pin 2 hot
(Unbalanced operation)
Input impedance 50 kilohms
Reference input level -56 dBm
Outputs
2 x standard mono phone jack
Output impedance 500 ohms
Reference output level
-10 to +4 dBm
Digital outputs
S/P DIF (coaxial, optical)
Control input
FS01
MIDI
IN, OUT, THRU
Dimensions
482 (W) x 115 (D) x 44 (H) mm
Weight
2.0 kg
Supplied accessory
Power cord
* 0 dBm = 0.775 Vrms
* Design and specifications subject to change without notice.
Troubleshooting / Specifications
Specifications
No sound or very low
volume
• Is sound source connected correctly to
INPUT jacks and are OUTPUT jacks
connected correctly to playback system?
Follow the instructions in "Getting Connected".
• Is a microphone connected to the rear-
panel INPUT jack?
Connect the microphone to the front-panel MIC
IN jack.
• Is unit in bypass mode and is MIX control
fully turned to the WET position?
Turn MIX control towards DRY.
• Is EDIT control knob 1 - 4 set to a position
where sound is cut off?
Turn EDIT control knob 1 - 4 clockwise.
• Are all shielded cables used for the
connection okay?
Try replacing the shielded cables.
Adjust the controls as described in the section
"Trying Out the Effects".
• Are the connected sound source and
playback system operating normally? Is the
volume set to a proper position?
• Are INPUT and OUTPUT controls of RFX-
2200 set to a proper position?
Check all components and set the volume to a
suitable position.
Input sound breaks up
or is distorted
• Is input signal level too high?
Adjust INPUT control so that CLIP LED does
not light at signal peaks.
• Is a line-level device such as a synthesizer
connected to the front-panel MIC IN
connector?
The sensitivity of the MIC IN connector is
optimized for microphones. Connect line-level
devices to the rear-panel INPUT jacks.
No effect sound
• Is incorrect foot switch connected?
Use only ZOOM FS01.
• Is RFX-2200 set to bypass mode?
Cancel the bypass mode.
Symptom Check Remedy
• Is MIC ON/OFF switch set to OFF?
To use a microphone plugged into the MIC IN
connector, the MIC ON/OFF switch must be set
to ON.
Troubleshooting
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom RFX2200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom RFX2200 in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info