121310

Zonder merk T861 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
displayed just to the right of the seconds count
Set current Date and Time
1. Press and hold the 'SET' button until the day (MO) starts flashing
2. Use the
'<-'
and
'->'
buttons to select the current day.
3. Press the 'SET' button the hours flash
4. Use the '<-' and '->' buttons to select the current hour.
5. Press the 'SET' button the minutes flash
6. Use the
'<-'
and '->' buttons to select the current minute.
7. Wait 5 seconds and the timer will drop out of time set mode back to normal mode.
Set Programmes
The unit has 20 separate timers each with separate On and Off times, each of
which can be set to act on a variety of different days of the week, e.g. every day
MO TU WE TH FR SA SU is selected or just weekends SA SU is selected, or a
single day e.g. only Wednesdays, WE is selected.
To set timers
1. Press the
'<-'
or
'->'
button
2. 1
0N
flashes, this indicates you are going to set the ON time of timer one, if
you want to set a different timer press the
'<-'
or
'->'
button to cycle
through the 20 ON and OFF timers.
3. Press 'SET' the days selection flashes
4. Use the '<-' and
'->'
buttons to select the days you wish this timer to operate on
5. Press 'SET' the hours f1ashe
6. Use the '<-' and '->' buttons to select the hour at which you wish this timer to operate
7. Press 'SET' the minutes flash
8. Use the
'<-'
and
'->'
buttons to select the minutes at which you wish this timer to operate
9. Press 'SET' the current timer, e.g. 1
0N
flashes
10. Use the '<-' and '->' buttons to select the next timer to set e.g. set 1
0FF
11. Repeat Steps 3 to 11 above
\
When done setting the timers wait 5" and the unit will go back to normal operating mode.
Operation
Once programmed the timer can be set using the triangular button with the picture of a finger,
there are three basic modes
1. OFF: always off
2. ON: always on
3. AUTO switches off and on based on the set timers.
When AUTO OFF is shown the timer socket is currently off, when AUTO ON is
shown the timer socket is currently on
Random Delay Start Mode (RND)
Random Delay Start mode delays the programmed start and finish times by between 2 and 32 minutes,
this can be used to give the impression that a timer is not being used to turn lights on and off.
1.
Press the RND button to enable or disable random mode.
2. If random mode is set "RND" appears on the right hand side ofthe display, blank in normal mode.
Countdown Timer Mode (CTO)
Countdown Timer Mode allows the timer to switch on after a pre-determined time delay, to
set CTD mode:
I
1. In normal mode, press
'<-'
to enter CTD mode
2. Press 'SET' and the
'<-'
an~ '->' keys to preset the countdown time (in the same way
as for the timer modes above)
3. Once back at the f1ashing ON display, press 'CTD' to start the countdown, 'CTD' is displayed
above the seconds countdown
4.
To pause and restart the countdown, press 'CTD' button
Red Indicator Lamp
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zonder merk T861 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zonder merk T861 in the language / languages: English as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info