729845
1
Zoom out
Zoom in
Previous page
1/2
Next page
ZE-RVC80MT MKII
MONTAGEANLEITUNG
RÜCKFAHRKAMERA
Die ZE-RVC80MT MKII eignet sich durch ihre kompakte Bauform auch zur Montage am Nummernschildhalter, oder unterhalb
des Stoßfängers, je nach Fahrzeugmodell und gewünschtem Resultat. Das von der Kamera wegführende Verbindungskabel kann
sehr oft durch die Zuführung der Nummernschildbeleuchtung gelegt werden. Auch bietet der hochwertige CMOS-Sensor einen
temperaturmässig erweiterten Einsatzbereich, sowie ein wasserdichtes (IP68) Gehäuse aus eloxiertem Aluminium-Druckguß.
BITTE BEACHTEN:
*
Fahrzeuge neueren Datums verwenden zur Stromversorgung der Fahrzeugaussenbeleuchtung eine über PWM Taktung generierte
(pulsierende) Spannung, welche für Bildsensor/Videoelektronik ungeeignet ist, bzw. Funktions- oder Bildstörungen zur Folge hat.
Verwenden Sie ausschließlich das mitgelieferte Anschlusskabel. Bei Nichtbeachtung erlischt Ihr Garantieanspruch.
*
Rotatable Reverse Camera / Winkelverstellbare Rückfahrkamera
Gelb: Video Out
Rot: ACC
Schwarz: GND
Grün: Kabel offen erzeugt gespiegeltes Bild.
Kabel auf GND gelegt erzeugt normales Bild.
Kamera kann
gedreht werden
Cinchstecker vom Videosignalkabel
mit dem Moni-/Naviceiver verbinden
Gelb: Batterie +12VDC
Form an „S“ shape with the cable
before you pull the cylinder out of the
bracket. Drill a mounting hole and fix the
bracket in place.
Formen Sie das Kabel zu einem “S”
bevor Sie den Zylinder aus der Kamera-
Halterung ziehen. Bohren sie ein Loch
und befestigen Sie die Halterung.
cylinder /
Zylinder
wire /
Kabel
Insert the cylinder into the bracket.
Attach the side cap piece.
Rotate the cylinder into desired view
angle. Tighten the screw.
Führen Sie den Zylinder in die Kamera-
Halterung ein. Drehen Sie den Zylinder
in die gewünschte Position und ziehen
Sie die Feststellschraube an.
Uncrew ths side cap. Cable goes
through the hole in the bracket and
remains invisible after the installation
is completed.
Schrauben Sie den seitlichen Teil der
Kamera ab. Das Kabel geht durch das
Loch in der Halterung und ist nach
Abschluss der Montage unsichtbar.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zenec ZE-RVC80MT MKII at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zenec ZE-RVC80MT MKII in the language / languages: English, German as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info