637197
4
Zoom out
Zoom in
Previous page
1/7
Next page
6 7
VOLUME CONTROL
ZENEC System
Multifunction steering wheel
1)
Function Button Operation
Increase volume
Turn volume knob (fig. S/01 ) clockwise.
Reduce volume
Turn volume knob (fig. S/01 ) counterclockwise.
Mute
Short press the rotary knob on the left (fig. S/01 ). Pressing
the button again will cancel the muting.
Default settings
The default settings of the different sources can be set in
Setup.
Device User Manual → Setup → Audio
Function Button Operation
Increase volume
+
Press button (fig. S/02) to increase volume.
Reduce volume
Press button (fig. S/02) to reduce volume.
Remote Control
Function Button Operation
Increase volume
Press button (fig. S/03 ) to increase volume.
Reduce volume
Press button (fig. S/03 ) to reduce volume.
Mute
Briefly press button (fig. S/03 ).
Pressing the button again will cancel the muting.
NOTE
1)
These functions can only be used when a multifunction steering wheel is installed in the vehicle,
and the ZENEC system is connected via a car specific CAN/Stalk interface.
TURN ON / OFF
Manual On / Off
Short press the rotary knob on the left, to turn the ZENEC system on, long press turn off
(fig. S/01
).
Automatic On / Off
Vehicles without CAN bus:
The device automatically switches on/off by ignition signal.
Vehicles with CAN bus interface:
Switching on the ignition will activate the ZENEC system. The boot process can take up to 1.5 minutes.
This may result in some delay until the system is ready. The ZENEC system is shut down by switching
off the ignition, or removing the ignition key.
BASIC OPERATION
The ZENEC system is equipped with an anti-theft protection function. If this is active, on restarting the
ZENEC system after interruption of the power supply you will be asked to enter your password.
To change the password:
Device User Manual → Setup → Device Setup → Help → Password
Z-E3726 5
GERÄTEBEDIENUNG Z-E3726
GRUNDSÄTZLICHE BEDIENUNG
EIN-/AUSSCHALTEN
Manuelle Ein-/Ausschaltung
Drehregler links gedrückt halten, bis sich das ZENEC-System ein- oder ausschaltet
(Abb. S/01 )
Automatische Ein-/Ausschaltung
Fahrzeuge mit CAN-Bus Anbindung: Bei Einschalten der Zündung wird das ZENEC-System
aktiviert. Der Bootvorgang kann max. 1,5 Minuten in Anspruch nehmen. Dies kann zur Folge
haben, dass das System nur mit Verzögerung einsatzbereit ist. Das Ausschalten des ZENEC-
Systems wird durch das Ausschalten der Zündung oder Abziehen des Zündschlüssels aktiviert.
HINWEIS
Für eine Nutzung des Multifunktionslenkrads sowie weiterer Fahrzeugfunktionen wird ein
fahrzeugspezifisches CAN/Stalk Interface benötigt. Weitere Informationen erhalten Sie bei einem
autorisierten ZENEC-Fachhändler.
DIEBSTAHLSICHERUNG
Das ZENEC-System ist mit einer Diebstahlschutzfunktion ausgestattet. Ist diese aktiv, werden Sie nach
Trennung der Stromversorgung bei erneutem Einschalten des ZENEC-Systems aufgefordert, das von
Ihnen hinterlegte Password einzugeben.
Um das Passwort zu ändern:
Bedienungsanleitung
Einstellungen
Geräte Konfiguration
Help
Passwort
HINWEIS
Bewahren Sie das
Passwort sorgfältig auf.
Bei einem Verlust des
Passworts muss das
ZENEC-System ausgebaut
und zur Freischaltung des
Diebstahlschutzes an den
ZENEC-Service
eingesendet werden.
Dieser Dienst ist
kostenpflichtig!
NOTE
Use of the multifunction steering wheel and other vehicle functions will require a vehicle-specific
CAN/Stalk interface. Further information may be obtained from an authorized ZENEC dealer.
ANTI-THEFT PROTECTION
NOTE
Keep your password safe.
If the password is lost the
ZENEC system must be
uninstalled, and sent back in
to ZENEC Service to release
the anti-theft protection.
There is a charge for this
service!
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zenec Z-E4626 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zenec Z-E4626 in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zenec Z-E4626

Zenec Z-E4626 User Manual - English - 49 pages

Zenec Z-E4626 Installation Guide - English - 7 pages

Zenec Z-E4626 User Manual - German - 49 pages

Zenec Z-E4626 Quick start guide - German - 7 pages

Zenec Z-E4626 Installation Guide - German - 7 pages

Zenec Z-E4626 User Manual - Dutch - 49 pages

Zenec Z-E4626 Quick start guide - Dutch - 7 pages

Zenec Z-E4626 Quick start guide - Spanish - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info