Manual Zanussi ZI457 (page 5 of 19) (English)

22313

Zoom out

Zoom in

1/19

PIN15GB

Remove all packaging before positioning the

machine.

Positioning

If possible, position the machine next to a water tap

and a drain.

This dishwasher is designed to be fitted under a

kitchen counter or sink (see “Building-in).

Water Outlet Connection

The end of the drain hose can be connected as

follows:

to the sink outlet siphon, securing it if necessary with

a clip;

to a wall outlet provided with vent-hole, minimum

internal diameter 4 cm;

The waste connection must be at a height of between

30 cm (minimum) and 100 cm (maximum) from the

floor.

It makes no difference which way the drain hose

faces, either to the right or left of the dishwasher.

Avoid bending or kinking the hose as this could

prevent or slow down the discharge of water.

If you use a drain hose extension it must be no longer

than 2 metres and its internal diameter must be no

smaller than the diameter of the hose provided.

Likewise the internal diameter of the couplings used

for connection to the waste outlet must be no smaller

than the diameter of the drain hose.

Water Supply Connections

This dishwasher may be fed with either hot (max.

60°C) or cold water.

Nevertheless we advise you a cold water supply.

A hot water supply is not always efficient with very

soiled crockery as it shortens the washing

programmes a lot.

Feeding the appliance with a hot water supply (max.

60°C) will allow you to obtain considerably shorter

programmes.

For making the connection itself, the coupling nut fitted

to the machine's supply hose is designed to screw

onto either a 3/4 inch gas thread spout, or to a

purpose-made quick-coupling tap such as the Press-

Block.

The water pressure must be within the limits given in

the technical specifications, as it will not function

correctly if pressure is outside these specifications.

The water supply hose is

fitted with a safety device,

which prevents water from

entering the machine

should the inner hose split,

due to wear.

The problem is signalled by a red indicator which

appears in window (B).

If this happens, close the water tap and have the hose

replaced.

Warning: the retaining ring (A) must be properly fitted

so as to avoid water leaks.

Note: the end of the

hose connected to the

machine can be positioned

as required, by simply

slackening the retaining

ring.

Re-tighten the ring securely

to avoid water leaks.

Avoid bends or kinks in the hose, which could prevent

or slow down the flow of water.

If the machine is connected to new pipes or pipes

which have not been used for a long time, you are

advised to run the water for a few minutes before

connecting the inlet hose. This will prevent deposits of

sand or rust clogging the inlet hose filter.

Electrical connection

Before plugging the appliance into the wall socket,

make sure that:

1. the mains voltage corresponds to the voltage given

in the technical specifications;

2. the meter, fuses, mains power supply and wall

socket can all take the maximum load required.

Make sure that the socket and plug are compatible

without having to use any type of adapter. If necessary,

have the domestic wiring system socket

replaced.

Safety standards require the appliance to be

earthed.

The Manufacturer accepts no liability for failure to

observe the above safety precautions.

CA01

min 30 cm

max 100 cm

+ 2 m max

min 4 cm

Ø 18

Ø 21

CA06

INSTALLATION

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zanussi ZI457 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zanussi ZI457

Zanussi ZI457 User Manual - Spanish - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zanussi ZI457 Manual

Product: