Manual Yardforce LT C25 (page 13 of 16) (English)

779852

Zoom out

Zoom in

1/16

24 25

OPERATION

WARNING: Dress properly to reduce the risk of injury when operating this tool. Do not

wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy duty, long

trousers, boots and gloves. Do not wear short trousers, sandals or go barefoot.

Before operating, look around you to ensure a safety working area without other people,

animals or any loose objects. And then check for eye protection, proper clothing and

balanced footing.

STARTING/STOPPING THE LINE TRIMMER

To Start (Fig. J)

Press down the lock-off lever and hold it in that position. Depress the trigger to start.

To Stop

Release the trigger.

NOTE: Always remove the battery pack from the line trimmer during work breaks and after

nishing work.

Height adjustment （Fig. K)

1. Loosen the locking sleeve counter clockwise.

2. Adjust the pole length to t your body height.

3. Tighten the locking sleeve anti-clockwise.

Handle adjustment

Adjust the angle of the auxiliary handle to ease operation and prevent loss of control.

1. Loosen the knob and move the handle up or downward.

2. Tighten the knob to secure the auxiliary handle in the adjusted position.

Tilt adjustment (Fig. L)

Adjust the vertical angle of the trimmer head to t the trimming conditions.

1. Press the tilt adjustment pedal down with your foot.

2. Adjust the angle of the pole, up or down.

3. Release the unlock pedal and keep moving the pole until it locks in place.

OPERATION

NOTE: Always ensure that the pedal snaps into place after adjusting the trimmer in one of the

three positions!

Edging (Fig. M)

1. Adjust the vertical angle of trimmer head to 0 degree by pressing the tilt adjustment

pedal.

2. Adjust the trimmer head to 90 degrees for edging by pressing the locking button.

3. Twist the plant protector to an angle of 90°.

Automatic line feeding

The equipment features a fully automatic single line system. The lines will automatically

elongate every time you turn on the appliance. To support proper line elongation, ensure that

the coil has stopped moving completely before turning on the appliance again.

The lines are automatically cut to the correct length by the line cutter.

Trimming

1. Ensure the knife protector label is removed before use. Ensure you wear gloves when

removing this label.

2. Adjust the trimmer head angle to a proper position for trimming operation.

3. Hold the grass trimmer rmly, keeping your balance with feet slightly apart. Alter the

height of the product if needed to ensure an upright posture.

4. Hold the trimmer head just above the ground at an angle of approximately 30°.

5. Move the product slowly from side to side in a swinging motion.

6. Ensure the cutting device remains clean and free from off-cuts that may cause it to jam.

Check regularly. Release the on/off switch and take the battery pack off before checking.

7. Trim longer grass in stages; do not cut long grass in one cut. For the best results, cut

longer grass in steps.

8. Place the trimmer along the edge of the lawn.

9. Turn product on and push the trimmer forward slowly.

Tips

1. For best results, do not cut wet grass as it tends to stick to the cutting head and guard,

prevents proper discharge of grass trimmings and could cause you to slip and fall.

2. Do not allow the spool cover to drag on the ground or other surfaces.

3. Pay special attention when performing work close to trees and bushes. The cutting head

could damage sensitive bark, and damage fence posts.

4. Fold the plant protector out to avoid bringing the cutting device into contact with hard

objects such as walls and curbstones.

NOTE: The trimming line will wear faster and require more feeding if the cutting or edging is

done along sidewalks or other abrasive surfaces or heavier weeds are being cut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yardforce LT C25 in the language / languages: English as an attachment in your email.

The manual is 1.19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yardforce LT C25

Yardforce LT C25 User Manual - German - 17 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yardforce LT C25 Manual

Product: