Carrying out AUTO SETUP for appropriate surround effects
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the
AUTO SETUP procedure is in progress.
1.
Place the IntelliBeam microphone at your normal listening position.
Assemble the cardboard microphone stand and place the IntelliBeam microphone on top of it horizontally as shown below.
Use the supplied cardboard microphone stand to place the IntelliBeam microphone at the same height as your ears would be when
you are seated.
Make sure that there are no obstacles between the IntelliBeam microphone and the walls in your listening room as these objects
obstruct the path of sound beams.
4.
Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack on the rear of the unit.
5.
Make sure that your listening room is as quiet as possible.
For accurate measurement, turn off air conditioner or other devices that make noises.
Follow the instructions below and then leave the room. If you remain in the room, you may obstruct the beam, or the microphone may
pick up any sounds you make, possibly resulting in improper configuration of settings.
When leaving the room, bring this Quick Reference Guide with you. The AUTO SETUP procedure takes about 3 minutes. Wait outside
the room during the AUTO SETUP procedure.
To cancel the AUTO SETUP procedure after it is started, press the RETURN () key on the remote control.
6.
Press the ENTER key to start the AUTO
SETUP procedure and then leave the room
within 10 seconds.
The screen automatically changes during the AUTO
SETUP procedure.
If the AUTO SETUP procedure is complete, this unit
rings the chimes and the results will be displayed on the
TV.
•The results displayed depend on the position of the
unit.
•If you hear a buzzer sound and an error message
appears on the TV, look for a solution in “If an error
message is displayed” on page 36 in the Owner’s
Manual.
7.
Press the ENTER key.
The measurement results are applied and saved in the
unit.
•You can save several measurement results by
pressing the SYSTEM MEMORY 1, 2, or 3 key. See
page 34 in the Owner’s Manual.
When the SYSTEM MEMORY 1 key is pressed, “M1
Saving” is displayed, and settings are saved.
•If ambient noise is picked up after measurement
begins, an error message is displayed in the “AUTO
SETUP COMPLETE” screen prompting you to begin
measurement again. Press the ENTER key to begin
measurement again.
8.
Remove the IntelliBeam microphone.
The IntelliBeam microphone is sensitive to heat, so
should not be placed anywhere where it could be
exposed to direct sunlight or high temperatures (such as
on top of AV equipment).
2.
Press the z key to turn on this unit.
3.
Turn the TV on and switch the TV’s input to
display video content from this unit.
When this unit is connected to the HDMI input on the TV (as
shown in “Connecting a TV and BD/DVD player” in this Quick
Reference Guide), switch the TV’s input to “HDMI1”.
You can select the language for the menu display.
Press and hold the SETUP () key until the “OSD
LANGUAGE” menu appears. Press the S/T key to select the
desired language. Press the SETUP () key again to exit the
setup menu.
12345
Remove
Fit in
Fit in
Place horizontally
Run
through
IntelliBeam microphoneUpper limit
Center height of
this unit
Within 1 m (3.3 ft)
Within 1 m (3.3 ft)
Listening
position
Cardboard
microphone stand
1.8m (6.0 ft)
or more
Lower limit
Center line
IntelliBeam microphone
Cardboard microphone stand
yTip
INTELLIBEAM MICPHONES
INTELLIBEAM MIC
AUTO SETUP
(PREPARATION & CHECK)
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from Sound Pro-
jector. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
IntelliBeam microphone (supplied)
Cardboard microphone
stand (supplied)
Note
AUTO SETUP START
Will begin in 10 sec.
Please leave the room.
----------
[RETURN]:Cancel
(After 3 min.)
SHOW RESULT
MEASUREMENT COMPLETE.
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
ENVIRONMENT CHECK:Success
BEAM MODE:5Beam/Plus2
yTips
AUTO SETUP COMPLETE
Please remove the MIC
from Sound Projector
and the listening position.
Press [SYSTEM MEMORY] key
to save set-up in the memory.
INTELLIBEAM MICPHONES
INTELLIBEAM MIC
InstallationConnectionSettingsPlayback
Playing back
Confirm that this unit and other devices are properly connected by playing a DVD or BD on the BD/DVD player. The following explains
the playback procedure when this unit, TV, and BD/DVD player are connected as shown in “Connecting a TV and BD/DVD player” in
this Quick Reference Guide.
■Enjoying TV
6
1
7
3
1.
Press the z key to turn on this unit.
2.
Turn on your TV and BD/DVD player connected to this unit.
3.
Press the HDMI1 key to select the BD/DVD player as the input
source.
4.
Switch the TV’s input to HDMI 1.
5.
Play back a DVD or BD on the BD/DVD player.
6.
Press the VOL (+/-) key to adjust the volume.
7.
Press the CINEMA DSP keys to set your sound preferences.
See page 40 in the Owner’s Manual.
When this unit does not play back, check the following
•The connection between this unit and BD/DVD player.
•The audio output settings of the BD/DVD player is set to digital sound output
(bitstream).
•The TV’s input is switched to this unit.
HDMI1
Input source name
yTips
1.
Select the desired TV channel.
2.
Press the TV key.
•When audio is output from the TV speaker, set TV’s audio
output to any option other than TV. See the instructions
manual of TV for more information.
•HDMI control function
You can use the TV remote control to operate this unit if your
TV supports the HDMI control function. See page 37 in the
Owner’s Manual.
yTips
■Listening to the sound from a Bluetooth device
You can listen to the wireless sound from a Bluetooth device, such as a smartphone or digital music player.
See also the instructions manual of the Bluetooth device for more information.
■HOME THEATER CONTROLLER app for smartphones and tablets
For detailed operation, refer to the Owner’s Manual on the supplied CD-ROM.
1.
Press the key on the remote control.
“Bluetooth” is selected as the input.
2.
Turn on the Bluetooth device to be paired, and perform pairing.
The operation varies depending on the device. Refer to the operation manual of the device.
•Perform pairing with the Bluetooth device and unit within 10 m (33 ft) of each other.
•Pairing is required for connecting a Bluetooth device for the first time.
3.
Select “YSP-2500 Yamaha” in the
Bluetooth device list on the device.
If a passkey (PIN) is required, enter the number
“0000”.
When pairing is completed, or a completion
message appears on the Bluetooth device.
4.
Play back a song on the Bluetooth device.
“BLUETOOTH”, or the name of the connected device,
is displayed in the front panel display. “_” is displayed
for non-alphanumeric characters in the device name.
BLUETOOTH
yTips
YSP-2500
Yamaha
PIN 0 00 0
123
456
789
0
HOME THEATER CONTROLLER, a dedicated control app for Yamaha Home Theater components, enables basic operation of this unit,
including the ability to turn it off, switch between input sources, adjust volume, and select a sound program, using a smartphone or
tablet.
•The following devices support this app.
-iPod touch (4th generation or later) running iOS 5.1.1 or later
-iPhone 3GS or later devices running iOS 5.1.1 or later
-iPad running iOS 5.1.1 or later
-Android (version 2.3.3 or later) devices
•This app uses Bluetooth wireless communication.
•Search “HOME THEATER CONTROLLER” on Apple’s App Store or Google Play’s website to download the app or obtain the latest
information on the app.
•Android is a trademark of Google Inc.
•iPad, iPhone, iPod, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Yamaha YSP-2500 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Yamaha YSP-2500 in the language / languages: English as an attachment in your email.
The manual is 0,91 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
