555607
3
Zoom out
Zoom in
Previous page
1/20
Next page
2En
English
CONNECTIONS
Youneedacommerciallyavailablespeakercable.
y
Thesizeand/ormaterialofaspeakercableaffectsonthe
soundquality.Therefore,werecommendyoutopurchase
ahigh-qualityspeakercabletoexerttheperformanceof
thisunit.
Notes
• Connect the (+) terminals on the amplier and the
speaker using one side of the cable. Connect the
(–) terminals on both components using the other
side of the cable.
• Connect the speaker to the center terminals of your
amplier, making sure not to reverse the polarity
(+, –). If the speaker is connected with reversed
polarity, the sound will be unnatural and lack bass.
• When using an amplier with a rated output power
higher than the nominal input power of the speaker,
care should be taken never to exceed the speakers
maximum input.
• The speaker may be damaged if certain sounds
are continuously output at high volume level.
For example, if sine waves from a test disc, bass
sounds from electronic instruments, etc., are
continuously output, or when the stylus of a
turntable touches the surface of a disc, reduce the
volume level to prevent the speaker from being
damaged.
• Please refer to the owners manual that came with
your amplier or receiver.
How to connect:
1 Loosentheknob.
2 Remove15mm(5/8”)ofinsulationfromeachendof
thecables,andtwisttheexposedconductorstogether
neatlyandtightly,asshownbelow.
15 mm
(5/8")
3 Insertthebarewireintothehole.
4 Tightentheknobandsecurethecable.
5 Testthermnessoftheconnectionbypullinglightlyon
thecableattheterminal.
Notes
• Do not let the bare speaker wires touch each other
as this could damage the speaker or the amplier,
or both of them.
• Do not insert the insulation coating into the hole.
The sound may not be produced.
When using a banana plug
1
Unscrewtheterminalknob.
2 Removethecoverbypullingittowardyou.
1
2
Banana plug
CONNECTION TO YOUR AMPLIFIER
Before making connection, make sure that the amplifier is switched off.
CENTER
+
Amplifier
NS-C901
Tighten
Black (–)
Red (+)
Loosen
Insulation coating
Bare wire
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha NS-C901 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha NS-C901 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info