27612
25
Zoom out
Zoom in
Previous page
1/28
Next page
4
iii
V
Montieren Sie die Tastatureinheit (A).
Setzen Sie die Tastatureinheit (A) so auf den fertigen Ständer,
daß die beiden Schrauben an ihrer Unterseite hinter den Winkel-
blechen mit Führungsschlitz an der Hinterseite des Ständers zu
liegen kommen. Schieben Sie die Tastatureinheit dann bis zum
Anschlag in die Schlitze. KLEMMEN SIE IHRE FINGER DA-
BEI NICHT EIN!!
Richten Sie die Schraubenbohrungen an der Unterseite der
Tastatureinheit mit den Bohrungen der Winkelbleche aus
(achten
Sie auch darauf, daß sie mittig auf dem Ständer steht, wie in der
Abbildung gezeigt). Schrauben Sie die Tastatureinheit dann mit den
vier 6 x 16 mm Senkschrauben 2 am Ständer fest.
B
Schließen Sie das Pedalkabel an.
Sichern Sie das Pedalkabel in den beiden Kabelhaltern an den
Seitenwänden. Der Stecker wird an die zugehörige Buchse an der
Unterseite der Tastatureinheit (A) angeschlossen. Der Stecker paßt nur
in einer Richtung in die Buchse (mit der Führungsnase zur Tastaturseite
des Instruments weisend — siehe Abbildung). Versuchen Sie nicht, den
Stecker falsch herum mit Gewalt in die Buchse zu drücken!
N
Den Spannungswähler einstellen.
Bevor Sie nun das Netzkabel anschließen, müssen Sie den
Spannungswähler (falls vorhanden) auf die örtliche Netzspannung
einstellen. Zum Verstellen drehen Sie den Spannungswähler mit
einem Schlitzschraubendreher, bis der richtige Spannungswert (110,
127, 220 oder 240) an der Pfeilmarkierung steht. Bei der Ausliefe-
rung werden alle Instrumente mit Spannungswähler auf “240” vor-
eingestellt.
Nachdem Sie den Spannungswähler richtig eingestellt haben,
können Sie nun das Netzkabel anschließen. In manchen Gebieten
wird ein Steckerdapter mitgeliefert, um den Anschluß an die evtl.
unterschiedlich geformte Steckdose zu ermöglichen.
M
Justieren Sie schließlich noch den Höhen-
versteller.
Zur Stabilisierung ist an der Unterseite des Pedalkastens (C) ein
Höhenversteller vorgesehen. Schrauben Sie den Höhenversteller
heraus, bis er fest auf dem Fußboden steht. Der Höhenversteller
sorgt für stabile Pedalbetätigung und ermöglicht eine präzise Rege-
lung des Betätigungshubs. Wenn er nicht fest auf dem Boden steht,
können beim Treten der Pedale Klangverzerrungen auftreten.
WICHTIG
Vergewissern Sie sich nach Zusammenbau und Aufstel-
lung des Clavinova noch einmal davon, daß alle Schrau-
ben fest angezogen sind.
Wenn der Ständer schief steht, komische Geräusch
erzeugt oder sich beim Spielen wackelig anfühlt, prüfen
Sie gemäß den unter Zusammenbau und Aufstellung
gegebenen Anweisungen, ob der Ständer richtig
zusammengebaut wurde, und ziehen dabei die einzelnen
Schrauben noch einmal nach.
V
Install the main unit (A).
Place the main unit (A) on the side panels (D) with the screws
on its bottom panel (toward the rear of the main unit) just behind
the grooves in the brackets located at the top of the side panels.
Then slide the main unit forward until it stops. WATCH YOUR
FINGERS WHEN DOING THIS!!
Align the holes on the bottom panel of the main unit with the
holes in the brackets on the side panels
(also center the main unit
to produce equal clearance on the left and right sides, as shown in
the illustration), then screw in and securely tighten the four 6 x
16 millimeter flat-head screws 2.
B
Connect the pedal cord.
Pass the pedal cord through the two cord holders on the side
panel. Plug the free end of the cord into the connector on the
bottom of the main unit (A). The plug only goes in one way (the
lug on the connector should face the keyboard-side of the main
unit, as shown in the illustration) — don’t try to force it in the
wrong way around.
N
Voltage Selector
Before connecting the AC power cord, check the setting of the
voltage selector which is provided in some areas. To set the se-
lector for 110V, 127V, 220V or 240V main voltages, use a “mi-
nus” screwdriver to rotate the selector dial so that the correct
voltage for your region appears next to the pointer on the panel.
The voltage selector is set at 240V when the unit is initially
shipped.
After the proper voltage has been selected connect the AC
power cord. A plug adaptor may be also provided in some areas
to match the pin configuration of the AC wall outlets in your
area.
M
Set the adjuster.
For stability, an adjuster is provided on the bottom of the
pedal box (C). Rotate the adjuster until it comes in firm contact
with the floor surface. The adjuster ensures stable pedal operation
and facilitates pedal effect control. If the adjuster is not in firm
contact with the floor surface, distorted sound may result.
IMPORTANT
After assembling the Clavinova, check once more to
make sure that all screws have been securely fas-
tened.
If the stand leans to the side, makes unusual noises, or
otherwise seems unstable during use, check and
tighten all screws while following the assembly instruc-
tions given above.
Danger Zone
Gefahrenzone
Zones dangereuses
Zona peligrosa
6 x 16 mm flat-head screws 2
6 x 16 mm Senkschrauben 2
Vis à tête plate de 6 x 16 mm 2
Tornillos de cabeza plana de 6 x 16 mm 2
A
D
D
A
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha CLP311 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha CLP311 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha CLP311

Yamaha CLP311 User Manual - German - 29 pages

Yamaha CLP311 User Manual - French - 29 pages

Yamaha CLP311 User Manual - Portuguese - 24 pages

Yamaha CLP311 User Manual - Swedish - 24 pages

Yamaha CLP311 User Manual - Spanish - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info