478507
2
Zoom out
Zoom in
Previous page
1/2
Next page
INSTALLATION
The power supply in the VP-1000 is capable of operation from 100 ~ 240 VAC at 50 or 60 Hz. If you
have a choice between these two voltage ranges, use the higher voltage to minimize losses in the AC
cable.
Connect the supplied DC Power Cable between the VP-1000 OUTPUT jack and the VL-1000 DC
48V IN jack, and connect the supplied Control
Cable between the VP-1000 CONTROL socket
and the VL-1000 CONTROL socket.
Turn the Circut Breaker on the VP-1000 rear
panel ON, then turn the VP-1000 MAIN switch
ON to activate the power supply. Always turn the
VP-1000 Circut Breaker and MAIN switch on
before turning on the VL-1000 P
OWER switch.
To assure long life of the components, a primary
consideration in setting up the VP-1000 is pro-
viding for adequate ventilation around the cabi-
net. The cooling system of the VP-1000 must be
free to draw cool air in at the bottom of the chas-
sis, and to expel warm air out of the rear panel.
Provide a few centimeters of space around each
side of the VP-1000. Avoid heating vents and
window locations that could expose the VP-1000
to excessive direct sunlight, especially in hot climates.
AC POWER CONNECTIONS
The VP-1000 Power Supply does not require any transformer re-wiring, nor any changing of a switch
position; the power supply will operate from either 230 or 120 Volt line voltages without configuration
changes.
However, the AC power cable/plug configuration will be somewhat different, depending on the coun-
try in which you purchased your power supply. In some countries, the VP-1000 is shipped with the
standard 230 Volt connector appropriate for your location. In those areas where there are multiple
230 Volt connectors in common use, the VP-1000 is shipped without the power connector; one may
be obtained at a local hardware or electrical supply store.
Pictorial diagrams of the common 230 and 120 Volt AC connectors in use are shown below. When
wiring your own connector, be absolutely certain to observe the proper polarity on the pin connec-
tions. Consult with an electrician if you have any doubts about your wiring!
Be sure that your house wiring is capable of sufficient current capacity on the 230 Volt circuit to be
used, especially if this circuit is shared with household appliances. It always is preferable to operate
the VP-1000 from a dedicated 230 Volt circuit with its own circuit breaker.
CIRCUIT DIAGRAM
Australian
PLUG
European
PLUG
USA PLUG UK PLUG
(U.S.A. version)
(viewed from plug prong side)
(European version)
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu VP-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu VP-1000 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info