674747
80
Zoom out
Zoom in
Previous page
1/140
Next page
Page 78
FT
DX
1200 OPERATING MANUAL
CW MODE OPERATION
USING THE BUILT-IN ELECTRONIC KEYER
Connect the cable from your keyer paddle to the front or rear panel
KEY
jack.
1. 3ress the
[
MODE
]
button to engage CW operation.
The
USB CW
icon will appear in the display. The
MONI
” icon will appear in the TFT display and the
CW monitor is activated.
A
DVICE:
If you press the “CW” mode, you will engage the
“CW 5everse” mode, whereby the “opposite” side-
band injection is used, compared to the “normal”
sideband. The
LSB CW
icon will appear in the
display if you select CW 5everse.
. 5otate the 0ain Tuning 'ial knob to select the de-
sired operating freTuency.
3. 3ress the
[
S
/
T
/
W
/
X
]
button to select the “
KEYER
”,
then press the
[
SELECT
]
button to select “
ON
.
The “
KEYER
” will appear in the display, con¿rming
that the built-in (lectronic .eyer is now active.
4. 5otate the
[
MIC/SPEED
]
knob to set the desired
sending speed 4 a 60 W30). Clockwise rotation
of the
[
MIC/SPEED
]
knob will increase the keying
speed.
A
DVICE:
The display will show the keying speed for 3
seconds whenever the
[
MIC/SPEED
]
knob is
turned.
When you press either the “'ot” or “'ash” side
of your paddle, the CW keying tone will auto-
matically be generated.
. 3ress the
[
BK-IN
]
button to engage automatic acti-
vation of the transmitter when you press either the
'ot” or “'ash” side of your paddle. The “
BK-IN
icon will appear in the TFT display.
6. CW operation utili]ing your paddle may now com-
mence.
A
DVICE:
When you utili]e your keyer paddle, the transmit-
ter will automatically be activated, and the CW
characters or a string of dots and dashes) will be
transmitted. When you release the keyer paddle con-
tacts, transmission will cease, and reception will be
restored after a brief delay. The delay time is user-
programmable, per the discussion on page 83.
[
MONI
]
Button
[
BK-IN
]
Button
ADVICE:
You may adjust the CW sidetone audio level setting
of 0enu item “
036 MONITOR LEVEL
”.
To adjust the 0oni Level
1) $ctivate the 021I circuitry, if necessary.
) 3ress and hold in the
[
MONI
]
button for one
second to enter the 0enu item “
036 MONITOR
LEVEL
”.
3) 3ress the
[
SELECT
] button
.
4) While keying, rotate the
[
VFO-B/CLAR
]
knob
or press the
S
T
button) to adjust the monitor
level.
) When you are satisfied with the setting, press
the
[
SELECT
]
button, then press the
[
MENU
]
button to save the new setting and exit to normal
operation.
If you set the
[
BK-IN
]
button to 2ff, you may prac-
tice sending CW with the sidetone only, without hav-
ing the signal go out over the air.
If you reduce power via the 0enu item
177 TX
MAX POWER
”, the $LC meter reading will increase
this is normal and does not indicate any problem
whatsoever because increased $LC voltage is being
used to lower the power).
[
SPEED
]
Knob
[
MODE
]
Button
80


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info