674747
65
Zoom out
Zoom in
Previous page
1/140
Next page
Page 63
FT
DX
1200 OPERATING MANUAL
1. 3ress the
[
BAND
]
button corre-
sponding to the $mateur band on
which you wish to operate.
. 3ress the
[
MODE
]
button to select the operating
mode.
3ress and hold in this button to toggle to the alternate
mode.
For example, In the LSB or USB modes, pressing
and holding in this button toggles between “LSB”
and “USB” mode.
A
DVICE:
By convention, LSB is used in the 7 0H] and lower
$mateur bands for SSB communication, and USB is
used on the 14 0H] and higher bands the 10 0H]
band is used for CW and data modes only).
3. 5otate the 0ain Tuning 'ial knob to adjust the oper-
ating freTuency. $lternately, you may use the
[
UP
]
[
DWN
]
scanning buttons on the
MH-31
B8
Hand 0i-
crophone to sweep up or down the current band.
4. 3ress the microphone
PTT
3ush To Talk) switch to
begin transmission speak into the microphone in a
normal voice level.
A
DVICE:
The
” indicator will light up in the L(' in-
dicators area, con¿rming that transmission is in
progress.
When transmitting in the $0 mode, set a maxi-
mum carrier) power output of  Watts via the
[
PROC/CAR
]
knob.
. $djust the microphone ampli¿er gain to match the
microphone and your voice level 3ress the
[
S
/
T
/
W
/
X
]
buttons to select the “
METER
”, then press the
[
SELECT
]
button to select “
ALC
”.
Close the
PTT
switch, and speak into the micro-
phone in a normal voice level.
In the SSB mode, adjust the
[
MIC/SPEED
]
knob so
that the $LC meter stays within the $LC ]one of the
meter up to half scale deÀection) on voice peaks.
SSB/AM MODE TRANSMISSION
[
POWER
]
Switch
[
MIC/SPEED
]
Knob
Main Tuning Dial Knob
[
BAND
]
Keys
[
MODE
]
Button
25W
In the AM mode, adjust the
[
MIC/SPEED
]
knob so
that the $LC meter does not deÀect at voice peaks.
A
DVICE:
The freTuency display will show the relative micro-
phone gain level for 3 seconds whenever the
[
MIC/
SPEED
]
knob is turned.
6. 5elease the
PTT
switch at the end of your transmis-
sion. The transceiver will return to the receive mode.
Adjust to keep under this level
65


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info