674747
45
Zoom out
Zoom in
Previous page
1/140
Next page
Page 43FT
DX
1200 OPERATING MANUAL
Using the
[
UP
]
/
[
DWN
]
buttons of the
supplied MH-31
B8
Hand Microphone
The
[
UP
]
[
DWN
]
buttons on the supplied
MH-31
B8
Hand 0icrophone may also be used to manually scan
the freTuency upward or downward.
The microphone’s
[
UP
]
[
DWN
]
buttons utili]e the
tuning steps of the 0ain
Tuning 'ial knob.
When the microphone
[
FST
]
button is pressed,
the tuning rate increases by
a factor of ten, in a manner
similar to the transceiver
front panel
[
FST
]
button.
A
DVICE:
You may independently set
the tuning steps of the
[
UP
]
[
DWN
]
buttons in the $0 and F0 modes. To set new
tuning steps, use 0enu items “
156 AM CH STEP
” and
157 FM CH STEP
”.
Keyboard Frequency Entry
The 2perating freTuency may be entered directly into
the current VF2, using the front panel
[
BAND
]
key but-
tons.
Example: Enter 14.250.00 MHz
1. 3ress the
[
ENT
]
button to
begin the direct freTuency
entry process. 1ow, begin-
ning with the first digit of
the freTuency the leftmost
digit), we will enter the re-
Tuired digits of the freTuency.
. 3ress, in order, the digits of the operating freTuency,
using the
[
BAND
]
buttons the freTuency entry digit
or decimal point is printed on the right side of the
buttons). In this example, enter
[
1.8
1
)]
Æ
[
10
4
)]
Æ
[
GEN
.
)]
Æ
[
3.5
2
)]
Æ
[
14
5
)]
Æ
[
50
0
)]
Æ
[
50
0
)]
Æ
[
50
0
)]
Æ
[
50
0
)]
The decimal point after the0H]” portion of the
freTuency must be entered, but no decimal point is
reTuired after the “kH]” portion.
3. 3ress the
[
ENT
]
button once more to complete the
operating freTuency entry. $ short “beep” will con-
¿rm that the entry was successful, and the new oper-
ating freTuency will appear on the display.
A
DVICE:
If you attempt to enter a freTuency outside the oper-
ating range of 30 kH] a 6 0H], the microprocessor
will ignore the attempt, and you will be returned to
the previous operating freTuency. If this happens,
please try again, taking care not to repeat the error in
the freTuency entry process.
Using the
[
VFO-B/CLAR
]
knob
You may change the VF2-
$ freTuency in 1 0 H ]
steps. 3ress the
[
MHz/μT
]
button located at the bot-
tom left of the
[
VFO-B/
CLAR
]
knob. The 1 0H]
steps will be applied to the
VF2-$ freTuency. The “
MHz 1MHz
” notation will ap-
pear in the display.
When tuning in 1 0H] steps, clockwise rotation of the
[
VFO-B/CLAR
]
knob will increase the freTuency, while
counter-clockwise rotation will decrease the freTuency.
MORE FREQUENCY NAVIGATION TECHNIQUES
CONVENIENCE FEATURES
45


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info