674747

Yaesu FTDX1200 Manual

38
Zoom out
Zoom in
Previous page
1/140
Next page
Page 36 FT
DX
1200 OPERATING MANUAL
BASIC OPERATION:
RECEIVING ON AMATEUR BANDS
CLAR
(
CLARIFIER
)
O
PERATION
The
[
RX CLAR
]
,
[
TX CLAR
]
,
[
CLEAR
]
buttons and
[
VFO-B/CLAR
]
knob are used to offset the receive freTuency,
the transmit freTuency, or both, from their settings on the VF2-$ freTuency. Four small numbers on the TFT 'isplay
show the current Clari¿er offset. The Clari¿er controls on the
FT
DX
1200
are designed to allow you to preset an offset up
to . kH]) without actually retuning, and then to activate it via the Clari¿er
[
RX CLAR
]
and
[
TX CLAR
]
buttons.
This feature is ideal for following a drifting station, or for setting the small freTuency offsets sometimes utili]ed in ';
“Split” work.
Here is the techniTue for utili]ing the Clari¿er
1. 3ress the
[
RX CLAR
]
button. The “
RX
” notation
will appear in the TFT 'isplay, and the programmed
offset will be applied to the receive freTuency.
. 5otation of the
[
VFO-B/CLAR
]
knob will allow
you to modify your initial offset on the Ày. 2ffsets of
up to . kH] may be set using the Clari¿er.
To cancel Clari¿er operation, press the
[
RX CLAR
]
but-
ton. The “
RX
” notation will disappear from the display.
A
DVICE:
Turning the Clari¿er off merely cancels the applica-
tion of the programmed offset from the receive and
or the transmit freTuencies. To clear the Clarifier
offset, and reset it to “]ero,” press the
[
CLEAR
]
but-
ton. The programmed offset is displayed in the small
multi-channel window of the freTuency display.
The Clari¿er operation including the offset freTuen-
cy) will be memori]ed independently on each VF2
stack of VF2-$ and VF2-B.
[
VFO-B/CLAR
]
Knob
[
RX CLAR
]
Button
[
TX CLAR
]
Button
[
CLEAR
]
Button
TXCLAR
$lternately, you may apply the Clarifier offset
to the transmit freTuency, without changing the
receive freTuency typically, for “split” '; pile-
ups).
[
VFO-B/CLAR
]
Knob
[
S
/
T
]
Button
7KH7XQLQJ2IIVHW,QGLFDWRUSURYLGHVDJUDSKLFDOUHSUHVHQWDWLRQRIWKH&ODUL¿HURIIVHW
In CW mode the factory default setting of the Tuning 2ffset Indicator shows the
CW Center Tuning, instead of Clari¿er 2ffset. If you wish to change this so that the
Clari¿er 2ffset is also displayed on CW, use the following procedure
[
SELECT
]
Button
1. 3ress the
[
MENU
]
button to enter the 0enu
mode.
. 5otate the
[
VFO-B/CLAR
]
knob or press the
S
T
button) to select 0enu item “
011 BAR
DISPLAY SELECT
”.
3. 3ress the
[
SELECT
]
button, then rotate the
[
VFO-B/CLAR
]
knob or press the
S
T
button)
to select “
CLAR
Clari¿er)” replacing the default
“
CW TUNE
CW TU1I1G)” selection).
4. 3ress the
[
SELECT
]
button, then press the
[
MENU
]
button to save the new setting and exit
to normal operation.
[
MENU
]
Button
[
Plus
(
+
)
Offset
]
[
Zero Offset
]
[
Minus
(–)
Offset
]
… 38 …


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info