Manual Yaesu FTDX1200 (page 35 of 140) (English)

674747

Zoom out

Zoom in

1/140

Page 33FT

1200 OPERATING MANUAL

momentary presses of the

[

]

0H] band button.

(ach $mateur band button may similarly have up

to three freTuencymode settings applied.



When the

[

MHz/μT

]

button located to the left of

the

[

VFO-B/CLAR

]

knob) is pressed, the “

MHz

”

notation will appear in the display, and then rota-

tion of the

[

VFO-B/CLAR

]

knob will change the

freTuency in 1 0H] steps.

6. 3ress the

[

ANT

]

button to select the ap-

propriate antenna for the band in use.

DVICE:

When you make an antenna selection,

that antenna is “remembered” by the

microprocessor in conjunction with the

VF2 register in use.

7. 3ress the

[

MODE

]

button to select the

desired operating mode.

5epeated presses of the

[

MODE

]

button step through the available se-

lections.

3ressing and holding the

[

MODE

]

button will toggle to the alternate

mode.

For example, In the LSB or USB modes, pressing

and holding the

[

MODE

]

button toggles between

“LSB” and “USB” mode.

DVICE:



By convention in the $mateur bands, LSB is

used on the 7 0H] and lower bands with the

exception of 60 meters), while USB is utili]ed on

the 14 0H] and higher bands.



When changing modes from SSB to CW, you

will observe a freTuency shift on the display.

This shift represents the BF2 offset between the

“]ero beat” freTuency and the audible CW pitch

tone) you can hear the pitch is programmed via

the 0enu item “

066 CW FREQ DISPLAY

”), even

1. Turn on the external 'C power supply.

. 3ress and hold in the front-panel

[

ON/OFF

]

switch

until the transceiver turns on. $fter

about five seconds ten seconds if the

optional -Tuning .it is connected), the

transceiver is ready for full operation.

3. The transceiver will start up on 7.000.000 0H]

LSB, or the previously used operating freTuency)

and normal operation may begin.

OTE:

To turn power off, press and hold in the front panel

[

ON/OFF

]

switch for one second.

4. 5otate the

[

]

knob to set a com-

fortable audio level of the incoming

signals or noise. Clockwise rotation

of the

[

]

knob increases the vol-

ume level.

OTE:

When using headphones, start by rotating the

[

]

knob counter-clockwise, then bring the volume level

up after you put the headphones on. This will mini-

mi]e the chance of damage to your hearing caused

by an unexpectedly high audio level.

. 3ress an appropriate

[

BAND

]

key corresponding to

the $mateur band on which you wish to begin opera-

tion.

DVICE:



2ne-touch selection of each

$mateur band between 1.8

and 0 0H] is provided.



The

1200

utili]es a triple band-stack VF2

selection techniTue, which permits storing up to

three favorite freTuencies and modes onto each

VF2 band register. For example, you may store

one freTuency each on 14 0H] CW, 5TTY, and

USB, then recall these freTuencies by successive,

Here is the typical start-up procedure for normal operation

[

POWER

]

Switch

[

]

Knob

Main Tuning Dial Knob

[

BAND

]

Keys

BASIC OPERATION:

RECEIVING ON AMATEUR BANDS

[

MODE

]

Button

[

ANT

]

Switch

Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yaesu FTDX1200 Manual

Product: