674747
12
Zoom out
Zoom in
Previous page
1/140
Next page
Page 10 FT
DX
1200 OPERATING MANUAL
CONNECTION OF ANTENNA AND POWER CABLES
3lease follow the outline in the illustration regarding the proper connection of antenna coaxial cables, as well as the 'C
power cable. The 'C power connector for the
FT
DX
1200
must only be connected to a 'C source providing 13.8 Volts 'C
10 ), and capable of at least 3 $mperes of current. $lways observe proper polarity when making 'C connection
The RED DC power lead connects to the Positive (+) DC terminal.
The BLACK DC power lead connects to the Negative (–) DC terminal.
We recommend the use of the
FP-1030A
US$ market only) $C 3ower Supply. 2ther models of power supplies may
be used with the
FT
DX
1200
, but the 13.8 V'C input voltage, 3 $mpere current capability, and 'C cable polarity
guidelines described above must be strictly followed.
1ote that other manufacturers may use the same type of 'C power connections as does your
FT
DX
1200
transceiver,
however, the wiring con¿guration may be different from that speci¿ed for your transceiver. Serious damage can be
caused if improper 'C connections are made consult with a Tuali¿ed service technician when in doubt.
The 100 V 5F voltage #100 W0-ohm) is applied to the T; 5F section of the transceiver while transmitting.
'o not touch the T; 5F section absolutely while transmitting.
3ermanent damage can result when improper supply voltage, or reverse-polarity voltage, is applied to the
FT
DX
1200
. The Limited Warranty on this transceiver does not cover damage caused by application of $C volt-
age, reverse polarity 'C, or 'C voltage outside the speci¿ed range of 13.8 V 10 . When replacing fuses, be certain
to use a fuse of the proper rating. The
FT
DX
1200
reTuires a  $ blade fuse.
ADVICE:
'o not position the
FT
DX
1200
in a location with direct exposure to sunshine.
'o not position the
FT
DX
1200
in a location exposed to dust andor high humidity.
(nsure adeTuate ventilation around the
FT
DX
1200
, to prevent heat build-up and possible reduction of performance
due to high heat.
'o not install the
FT
DX
1200
on an unstable desk or table. 'o not place in a location where objects may fall onto it from above.
To minimi]e the possibility of interference to home entertainment devices, take all precautionary steps including
separation of TVF0 antennas from $mateur transmitting antennas to the greatest extent possible, and keep trans-
mitting coaxial cables separated from cables connected to home entertainment devices.
(nsure that the 'C power cord is not subject to undue stress or bending, which could damage the cable or cause it to
be accidentally unplugged from the rear panel
DC IN
jack.
Be certain to install your transmitting antennas) so they cannot possibly come in contact with TVF0 radio or other
antennas, or with power or telephone lines.
INSTALLATION AND INTERCONNECTIONS
To prevent damage from
lightning, atmospheric elec-
tricity, electrical shock etc., please
provide a good earth ground.
Use a short,
thick, braided
cable to con-
nect your station
eTuipment to the
buried ground rod or alternative earth
ground system).
Check the DC volt-
age and current rating
(+13.8 V, 23 A) of the power
supply before connecting to the
transceiver.
12


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ftdx1200

Reset search

  • Green Light on VFO A and MEM is flashing and no audio. Even tried Factory Reset and still flashing. How do I fix this? Submitted on 6-12-2022 at 07:37

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FTDX1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FTDX1200 in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info