674740
121
Zoom out
Zoom in
Previous page
1/154
Next page
Page 119FT-991 OperaTing Manual
Data (psk) operation
exAMple oF dAtA coMMunicAtionS device
Software Settings
note:
There are many good Data Mode Operating Software
programs available on the internet. Each of these pro-
grams will have their own Setup instructions, therefore
to assist you, the following, while general in nature is
common to most software setup.
COM PORT Settings
To start set the Com Port setting to the Enhanced
Driver. If there is a problem switch to the Standard
Driver.
PTT Settings
Set the PTT to RTS on DTR off.
SOUNDCARD
a. At the software Soundcard setting, set to USB CO-
DEC AUDIO
b. At the software Soundcard Volume setting increase
the volume to about 70% to start.
Advice:
If the soundcard volume setting is to low the radio
will not switch to Transmit.
DATA MODE
(PSK, OLIVIA, CONTESTIA, RTTY etc.)
FT-991 Settings
1. Press the
MODE
button, and then touch the corre-
sponding key on the LCD to select the DATA-USB
operating mode. The
D-U
” icon appears in the dis-
play.
Advice:
USB is the conventional mode for Digital (not
RTTY) transmission on all bands, however some us-
ers may be using LSB.
2. Press the
MENU(SETUP)
button. The Menu list
will appear in the display.
3. Rotate the
MULTI
knob to nd Menu item
062
”,
063
”, “
070
”, “
071
” or “
072
”.
4. Touch
[
SELECT
] on the LCD.
5. Rotate the
MULTI
knob to set these Menu item as
shown below.
Menu Function Setting
062 DATA MODE PSk
063 PSk TONE
Adjust for desired
center frequency.
070 DATA IN SELECT MIC
071 DATA PTT SELECT RTS
072 DATA PORT SELECT USB
6. Touch
[
ENTER
]
on the LCD, then press the
MENU(SETUP)
button or touch
[
BACK
]
on the
LCD to exit to normal operation.
note:
All other SSB and DATA settings remain at their de-
fault.
Connect a USB Cable from the FT-991 USB port
and your computer
Advice:
Before connecting the USB cable you must down load
the SCU-17 Drivers. The Drivers can be found on the
FT-991
FILES page at the Yaesu Web page, www.
yaesu.com. Once the Drivers have been installed con-
nect the USB cable to the computer and then to the ra-
dio. At your computers Device Manager you will nd
a Standard Driver and Enhanced Driver installed.
Computer Settings
Soundcard
At your Computer Control Panel Sound set your
Speaker Audio default to USB AUDIO CODEC.
COM PORT
Check your Com Port assignments at your Computer’s
Device Manager to be sure you have the Enhanced
and Standard Drivers. Make a note of the Com Port
numbers assigned.
Software Settings
note:
There are many good Data Mode Operating Software
programs available on the internet. Each of these pro-
grams will have their own Setup instructions, therefore
to assist you, the following, while general in nature is
common to most software setup.
COM PORT Settings
To start set the Com Port setting to the Enhanced
Driver. If there is a problem switch to the Standard
Driver.
PTT Settings
Set the PTT to RTS on DTR off.
SOUNDCARD
a. At the software Soundcard setting, set to USB CO-
DEC AUDIO
b. At the software Soundcard Volume setting increase
the volume to about 70% to start.
Advice:
If the soundcard volume setting is to low the radio
will not switch to Transmit.
121


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-991 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-991 in the language / languages: English as an attachment in your email.

The manual is 30,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info