674740
99
Zoom out
Zoom in
Previous page
1/154
Next page
Page 97FT-991 OperaTing Manual
convenient MeMory FunctionS
The
FT-991
contains ninety-nine regular memories, labeled “
01
” through “
99
”, nine special programmed band edge
memory pairs, labeled “
P-1L
/
P-1U
” through “
P-9L
/
P-9U
”, and ve QMB (Quick Memory Bank) memories. Each mem-
ory stores various settings, in addition to the VFO-A frequency and mode, but also stores the various settings shown be-
low. By default, the 99 regular memories are contained in one group; however, they can be arranged in up to six separate
groups, if desired.
quick point:
The
FT-991
memory channels store the following
data (not just the operating frequency):
VFO-A Frequency
VFO-A Mode
Clarier status and its Offset Frequency
IPO status
Attenuator status
Noise Blanker status
IF SHIFT and WIDTH status
CONTOUR status and its Peak Frequency
DSP Noise Reduction (DNR) status and its
Reduction algorithm selection.
DSP Notch lter (NOTCH) status
NAR bandwidth status
DSP Auto Notch lter (DNF) status
Repeater Shift Direction
CTCSS Tone information (CTCSS Encode,
Decode ON/OFF; Tone Frequency)
DCS information (DCS On/Off, DCS Code)
MeMorY operation
qMb MeMory bAnk
regulAr MeMory chAnnelS
pMS MeMory chAnnelS
01
97
P-7L/7U
P-6L/6U
P-5L/5U
P-4L/4U
02
98
P-8L/8U
03
99
P-9L/9U
P-1L/1U
P-2L/2U
P-3L/3U
qMb
(
quick MeMory bAnk
)
The Quick Memory Bank consists of ve memories independent from the regular and PMS memories. The QMB mem-
ories can quickly store operating parameters for later recall.
QMB Channel Storage
1. Tune to the desired frequency on VFO-A.
2. Press and hold the
RCL/STO
button for one second.
The “beep” will confirm that the VFO-A contents
have been written to the currently available QMB
memory.
Repeated one second presses of the
RCL/STO
but-
ton will write the VFO-A contents to successive QMB
memories.
Once all ve QMB memories have data on them, previ-
ous data will be over-written on a rst-in, rst-out basis.
QMB Channel Recall
1. Press the
RCL/STO
button briefly. The current
QMB channel data will be shown on the frequency
display area. The
QMB
icon will also appear and
the Memory Mode indicators in the LED indicators
area will illuminate.
2. Repeated brief presses of the
RCL/STO
button will
toggle through the QMB channels.
3. Press the
V/M
button to return to the VFO or Memo-
ry mode.
RCL/STO Button
V/M Button
Advice:
Rotating the Main Tuning Dial knob, or changing the
operating mode, will place the transceiver in the “Mem-
ory Tune” mode, which is a temporary “pseudo-VFO”
method of tuning off of a stored memory channel. If you
do not over-write the contents of the current memory
channel, the original contents will not be disturbed by
the initiation of Memory Tune operation.
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-991 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-991 in the language / languages: English as an attachment in your email.

The manual is 30,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info