478500
59
Zoom out
Zoom in
Previous page
1/76
Next page
Page 57FT-897D OPERATING MANUAL
MENU MODE No015
[
CAR LSB R
]
Function: Sets the Rx Carrier Point for LSB.
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No016
[
CAR LSB T
]
Function: Sets the Tx Carrier Point for LSB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No017
[
CAR USB R
]
Function: Sets the Rx Carrier Point for USB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No018
[
CAR USB T
]
Function: Sets the Tx Carrier Point for USB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No019
[
CAT RATE
]
Function: Sets the transceivers circuitry for the CAT baud
rate to be used.
Available Values: 4800bps/9600bps/38400bps
Default: 4800bps
MENU MODE No020
[
CAT/LIN/TUN
]
Function: Selects the device which is connected to the
CAT/LINEAR jack on the rear panel.
Available Values: CAT/LINEAR/TUNER
Default: CAT
MENU MODE No021
[
CLAR DIAL SEL
]
Function: Defines the “control” knob to be used for setting
of the clarifier offset frequency.
Available Values: CLAR, M/V, MAIN (Clarifier/Selector/
Main Dial Knobs)
Default: CLAR
MENU MODE No-022
[
CW AUTO MODE
]
Function: Selects whether the KEY jack shall be “Enabled”
or “Disabled” while using the SSB/FM modes.
Available Values: ON/OFF
Default: OFF
OFF: The KEY jack is enabled on the CW mode only.
ON: The KEY jack is enabled on all modes (SSB mode:
A1, FM mode: F2). Thus, on SSB, you can ask a
station for a CW QSO without having to change your
FT-897Ds Mode selection, if Menu #022 is set to
“On.”
MENU MODE No023
[
CW BFO
]
Function: Sets the CW carrier oscillator injection side on
the CW mode.
Available Values: USB/LSB/AUTO
Default: USB
USB: Injects the CW carrier oscillator on the USB side
LSB: Injects the CW carrier oscillator on the LSB side
AUTO:Injects the CW carrier oscillator on the LSB side
while operating on the 10 MHz band and below, USB
side while operate on the 10 MHz band and up.
MENU MODE No-024
[
CW DELAY
]
Function: Sets the receiver recovery time during pseudo-
VOX CW semi-break-in operation.
Available Values: FULL/30 ~ 3000 msec
Default: 250 msec
The recovery time may be adjusted in steps of 10 msec. A
longer delay may be preferable if you pause frequently while
sending.
MENU MODE No025
[
CW KEY REV
]
Function: Sets the keyer paddle’s wiring configuration.
Available Values: NORMAL/REVERSE
Default: NORMAL
NORMAL: Keyer paddle polarity is normal. The “tip” plug
connection produces dots, and the “ring” plug
connection produces dashes.
REVERSE: Keyer paddle polarity is inverted. The “tip”
paddle produces dashes, and the “ring” paddle
produces dots.
MENU MODE No026
[
CW PADDLE
]
Function: Enables/disables CW keying by the microphone’s
[UP]/[DWN] keys.
Available Values: ELEKEY/MICKEY
Default: ELEKEY
When this Menu Item is set to “MICKEY,” press the
microphone’s [UP] key to send a “dot,” and press the
microphone’s [DWN] key to send a “dash” (while the built-
in electronic keyer is engaged).
MENU MODE No-027
[
CW PITCH
]
Function: Setting of the pitch of the CW sidetone, BFO
offset, and CW filter center frequencies.
Available Values: 400 ~ 800 Hz
Default: 700 Hz
The CW pitch may be adjusted in steps of 100 Hz.
MENU MODE No028
[
CW QSK
]
Function: Selects the time delay between when the PTT is
keyed and the carrier is transmitted during QSK operation
when using the internal keyer.
Available Values: 10/15/20/25/30 ms
Default: 10 ms
Note: If you select “25 (or 30) ms,” please do not attempt
to set Menu [No-030 CW SPEED] to a speed faster than
“50 (42) wpm,” as the delay will make it impossible to trans-
mit.
MENU MODE No-029
[
CW SIDE TONE
]
Function: Setting of the CW sidetone volume level.
Available Values: 0 ~ 100
Default: 50
MENU OPERATION
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info