478500

Yaesu FT-897D Manual

40
Zoom out
Zoom in
Previous page
1/76
Next page
Page 38 FT-897D OPERATING MANUAL
DIGITAL MODE OPERATION
(
SSB-BASED AFSK
)
The FT-897D provides extensive capability for digital mode
operation on the HF, VHF, and UHF bands. The use of AFSK
(Audio Frequency-Shifted Keying) configurations allows a
wide variety of different communication modes to be uti-
lized. The Menu provides for specific digital mode selec-
tions, which include custom BFO offsets to optimize the
receive and transmit passbands for the mode selected.
Before beginning Digital operation, you need to define which
Digital mode will be utilized. To do this, use Menu #38 as
follows (in this example, we will set up RTTY as the Digital
mode):
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-038
[
DIG MODE
]
.
3. Rotate the DIAL knob to select “RTTY-L” or “RTTY-U”
(see discussion below).
4. Press and hold in the
[
F
]
key for one second to save the
new setting and exit.
Use this technique to set up any digital mode.
RTTY
(
Radio TeleType
)
Operation
The “RTTY” mode on the FT-897D is available in either
LSB-side or USB-side BFO injection. Long-standing Ama-
teur practice calls for the use of LSB-side injection, but some
applications require that you use USB-side injection.
1. Connect your TNC (Terminal Node Controller) or ter-
minal modem to the FT-897D’s rear-panel DATA jack,
per the illustration. Be sure to use the “TX AUDIO” line,
not an “FSK” line, for the transmit data connection to
the FT-897D.
TRANSMITTER OPERATION
3. If the optional YF-122C 500 Hz filter or YF-122CN
300 Hz filter filter has been installed, it may be used for
RTTY work. Recall Multi Function Row “n”
[
CFIL, -----,
-----
]
, then press the
[
B
](
-----
)
or
[
C
](
-----
)
key to engage the
narrow filter.
4. To set up the transmit side, be sure that the Meter is set
to monitor ALC voltage. If not, press the
[
F
]
key mo-
mentarily, then rotate the MEM/VFO CH knob to select
to select Multi Function Row “i”
[
MTR, -----, DISP
]
, then
press the
[
A
](
MTR
)
or
[
B
]
key so as to select metering
of ALC (“ALC” icon will appear at the upper of the
[
B
]
key).
5. Press and hold in the
[
F
]
key for one second to enter the
Menu mode, then rotate the MEM/VFO CH knob to se-
lect Menu Mode No-037
[
DIG GAIN
]
.
6. Following the instructions for your TNC’s software, ac-
tivate the transmitter from the computer keyboard; this
should cause the AFSK output from the TNC to be sent
to the radio. While transmitting, view the ALC meter; a
few “dots” of ALC indication should be observed. If not,
rotate the DIAL knob to adjust the AFSK level within
the FT-897D for seven to eight dots of indication on the
ALC meter.
7. Press and hold in the
[
F
]
key for one second to save the
new AFSK level setting and return to normal operation.
You are now ready for full RTTY operation.
Because RTTY is a continuous-duty transmis-
sion mode, try to keep your transmission short
when running on battery power, so as to mini-
mize current drain.
PTT
DATA IN
GND
AFSK
OUT
AF IN PTT
DATA OUT
2. Press the MODE
(
)
or MODE
(
)
key, as needed, to
select the DIG mode (the “DIG” icon will appear on the
display). You should now be able to tune around the band,
and any RTTY signals heard should be capable of being
decoded.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info