478499

Yaesu FT-857D Manual

59
Zoom out
Zoom in
Previous page
1/132
Next page
57FT-857D Operating Manual
TRANSMITTER OPERATION
FM TRANSMISSION
Repeater Operation
1. Press the
[
FUNC
]
key momentarily, then rotate the SELECT knob, as needed, until
Multi Function Row “d”
[
RPT, REV, VOX
]
appears on the display.
2. Press the
[
A
](
RPT
)
key to activate repeater operation. One press of the
[
A
](
RPT
)
key
will have set the transceiver for “Minus Shift” operation. In this situation, you will
observe the “–” indicator on the display. The transmitter frequency will be shifted down
by a default value so as to access the repeater input frequency. If your repeater uses a
positive shift (instead of negative), press the
[
A
](
RPT
)
key again; the “+” indicator will
replace the “–” indicator on the display. Set the transceiver’s receiver to the repeater
output (downlink) frequency. Close the PTT switch and speak into the microphone.
You will observe that the transmitted frequency has shifted according to the setting of
the
[
A
](
RPT
)
key in the Multi Function Row “d”
[
RPT, REV, VOX
]
. Release the PTT
switch to return to the Receive mode.
3. If the default repeater shift is not appropriate for the majority of the repeaters your area,
it may be set independently for each band. To
change the default repeater shift:
Press and hold in the
[
A
](
RPT
)
key for one
second. This instantly recalls Menu Mode No-
076
[
RPT SHIFT
]
.
Rotate the DIAL knob to select the desired shift
frequency.
When done, press and hold in the
[
FUNC
]
key
for one second to save the new setting and exit
to normal operation.
4. If your repeater uses controlled access (using either CTCSS or DCS), press the
[
FUNC
]
key momentarily, then rotate the SELECT knob one click clockwise to cause Multi
Function Row “e”
[
TON, –––, TDCH
]
to appear on the display. Now select the appro-
priate tone access system:
Press the
[
A
](
TON
)
key to activate the CTCSS tone encoder, which provides a
subaudible repeater access tone. One press of the
[
A
](
TON
)
key will activate the
CTCSS tone encoder. In this situation, you will observe the “TEN” indicator on the
display. If you press the
[
A
](
TON
)
key repeatedly, you will observe “TSQ” (CTCSS
Encode/Decode), “DEN” (Digital Coded Squelch, Encode), followed by “DCS” (Digi-
tal Coded Squelch, Encode/Decode). One additional press will disable all repeater-
access tone systems. See the next section for a discussion of DCS operation.
If the default repeater access tone is not appropriate for the repeater on which you
are operating, it may be set easily:
(1) Press and hold in the
[
A
](
TON
)
key for one second. This instantly recalls Menu
European Version
Version A
2-m
145.1 145.5
145.6 145.8
146.0 146.4 147.0 147.6 148.0
146.6 147.4
Euro Version 1
Euro Version 2
Version A
70-cm
440.0 445.0 450.0
439.45438.20
433.00 433.40
ARS-Repeater Subbands
… 59 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-857D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-857D in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info