478498

Yaesu FT-817ND Manual

47
Zoom out
Zoom in
Previous page
1/84
Next page
45FT-817ND Operating Manual
MEMOR Y OPERATION ON “REGULAR•EM EMOR Y CHANNELS
Normal Memory Storage
1. Tune in the desired frequency, and set the operating mode and bandwidth. If this is an
FM channel, set up any required CTCSS/DCS and repeater shift configurations. Stan-
dard (default) repeater shifts do not require you to utilize the “split” frequency memory
technique, described later.
2. Press the key momentarily, then rotate the knob, as needed, until Operating
Function Row 2
[
MW, MC, TAG
]
appears on the display.
3. Press the
(
MW
)
key momentarily to enter the “Memory Check” mode, which is
used to find an unused memory channel. The frequency stored (if any) on the current
memory channel will be shown in the display.
4. Rotate the knob to select the channel number on which you wish to store the
current frequency data.
5. Press and hold in the
(
MW
)
key for one second until you hear a double beep; the
second beep confirms that the frequency information was successfully stored.
Split-Frequency Memory Storage
You can also store “Split” frequencies, such as when operating on a repeater system not
utilizing a “standard” offset. This procedure may also be used for DX work on 7 MHz SSB, etc.
1. In the VFO mode, set the desired Receive frequency and mode.
2. Press the key momentarily, then rotate the knob, as needed, until Operating
Function Row 2
[
MW, MC, TAG
]
appears on the display.
3. Press the
(
MW
)
key momentarily to enter the “Memory Check” mode, which is
used to find an unused memory channel. The frequency stored (if any) on the current
memory channel will be shown in the display.
4. Rotate the knob to select the channel on which you wish to store the receive
frequency data.
5. Press and hold in the
(
MW
)
key for one second until you hear a double beep, which
confirms that the Receive frequency data is now stored.
6. Now, set the desired Transmit frequency and mode on the VFO.
7. Press the
(
MW
)
key momentarily; do not rotate the knob!
8. While the “memory channel number” is blinking, press and hold in the PTT switch;
while holding it in, press and hold in the
(
MW
)
key for one second. The double
“beep” will confirm that independent Transmit frequency data is now stored. You may
now release the PTT switch.
In step 8 above, pressing the PTT switch does not activate the transmitter. It sim-
ply sends a signal to the microprocessor that an independent Transmit frequency
is being stored on the same channel as a previously-stored Receive frequency.
MEMORY OPERATION
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-817ND at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-817ND in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info