478497

Yaesu FT-2000D Manual

136
Zoom out
Zoom in
Previous page
1/140
Next page
Page 134 FT-2000D OPERATING MANUAL
I
NSTALLATION
OF
THE
O
PTIONAL
F
ILTER (YF-122C
OR
YF-122CN)
1. Turn the FT-2000D’s
[
POWER
]
switch “off,” then
turn the FP-2000’s
[
POWER
]
switch “off.”
2. Unplug the AC cable from the AC jack on the FP-
2000 rear panel.
3. Disconnect the all of the cables from the transceiver.
4. Referring to Figure 1, remove the three screws from
each side of the transceiver, and three screws from the
top edge of the rear panel. Slide the top cover toward
to the rear about 1/2 inch (1 cm), then remove the top
cover.
5. Refer to Figure 2 for the mounting location for the
optional filter. Position the filter so that its connectors
are aligned with the mounting pins on the board, and
push it into place.
6. Replace the top cover and its nine screws.
7. Filter installation is now complete. Now you must en-
able the newly-installed filter, using the Menu.
8. Connect the two DC cables to the FT-2000D rear panel,
and then connect the AC cable to the AC jack on the
FP-2000 rear panel.
9. Turn the FP-2000’s
[
POWER
]
switch “on,” then turn
the FT-2000D’s
[
POWER
]
switch “on.”
10. Press the
[
MENU
]
button momentarily to engage the
Menu mode.
11. Rotate the Main Tuning Dial knob to select the Menu
item “
037 GEnE SUB FIL037 GEnE SUB FIL
037 GEnE SUB FIL037 GEnE SUB FIL
037 GEnE SUB FIL.”
12. Rotate the
[
SUB VFO-B
]
knob to choose the selec-
tion appropriate for the filter you have just installed
(“
300300
300300
300” for YF-122CN, “
500500
500500
500” for YF-122C).
13. Press and hold in the
[
MENU
]
button for two seconds
to save the new setting and exit to normal operation.
FIGURE 1
FIGURE 2
RX-2 UNIT
Optional Filter
RX-2 UNIT
… 136 …


Need help? Post your question in this forum.

Forumrules
1

Forum

yaesu-ft-2000d

Reset search

  • My FT2000D will not Transmit. Have not used it in over a year. I am sure it is something I have done wrong. Whe u puss PTT the signal goes to ZERO. Please Advise! Submitted on 12-9-2020 at 00:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-2000D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2000D in the language / languages: English as an attachment in your email.

The manual is 7,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info