674722
47
Zoom out
Zoom in
Previous page
1/56
Next page
DR-2X / DR-2XE Operating Manual 45
Setting to connect the repeater controller S-COM7330
Set up instructions to interface the Triple Repeater Controller S-COM7330 with the DR-2X/DR-2XE.
Modification of S-COM7330
1 Remove the 6 screws from each side and 2 screws from the top
cover of the S-COM7330, then remove the top cover.
2 Change Jumper pin J10C or J11C or J3C and adjust the semi fixed.
AF volume gain up for RX1 or RX2 or RX3.
3 Command Settings.
Select Path Access Mode: Carrier and CTCSS
Select COR Filter Delay: 300 msec
Select Dropout Delay: 0 sec
Setting of DR-2X/DR-2XE
Set the DR-2X/DR-2XE as follows.
Setting the communication mode RX: AUTO (AMS)
TX: FM (FIX)
Setting the tone signals: RX-TONE (100 Hz) (see page 35)
Connection with S-COM7330 and DR-2X/DR-2XE
DR-2X/DR-2XE S-COM7330 Connection
pin 1 EXT I/O pin 1 RX Audio Connect to DR-2X/DR-2XE AF out
pin 2 EXT PTT pin 2 RX COR Connect to DR-2X/DR-2XE SQL DET
pin 3
CTCSS/DCS DET
pin 3 CTCSS in
Connect to DR-2X/DR-2XE CTCSS/DCS decode
output
pin 4 SQL DET pin 4 TX PTT Connect to DR-2X/DR-2XE EXT PTT
pin 5 GND pin 5 TX Audio Connect to DR-2X/DR-2XE AF in
pin 6 TONE IN pin 6 GND DR-2X/DR-2XE GND
pin 7 AF IN pin 7 GND DR-2X/DR-2XE GND
pin 8 DISC OUT pin 8 TX pin 8 Select TX LOGIC or TX CTCSS by JP pin
pin 9 AF OUT pin 9 GND DR-2X/DR-2XE GND
pin 10 GND
I/O Controller
pin 1 to 6
Logic output
Connect to DR-2X/DR-2XE EXT I/O
(needs S-COM programming)
pin 11 EXT PORT1
I/O Controller
pin 1 to 6
Logic output
Connect to DR-2X/DR-2XE EXT PORT1
(needs S-COM programming)
pin 12 EXT PORT2
I/O Controller
pin 1 to 6
Logic output
Connect to DR-2X/DR-2XE EXT PORT2
(needs S-COM programming)
pin 13 EXT PORT3
I/O Controller
pin 1 to 6
Logic output
Connect to DR-2X/DR-2XE EXT PORT3
(needs S-COM programming)
pin 14 EXT PORT4
I/O Controller
pin 1 to 6
Logic output
Connect to DR-2X/DR-2XE EXT PORT4
(needs S-COM programming)
pin 15 VCC OUT DC jack DC in Connect to DR-2X/DR-2XE VCC out
The wiring paths shown by the dotted lines require programming the S-COM7330.
pin 1 EXT I/O Jumper to pin 2 EXT PTT or connect to S-COM7330 LOGIC OUT (L: EXT I/O enable)
pin 2 EXT PTT EXT PTT input from S-COM7330. It will be controlled by RX COR normally.
pin 3
CTCSS/DCS DET
Signaling decode output (CTCSS/DCS etc)
pin 4 SQL DET Noise SQL decode output (Connect to RX COR)
pin 5 GND GND
pin 6 TONE IN Tone input from S-COM7330 (Connect to TX pin8)
pin 7 AF IN Modulation input from S-COM7330
pin 8 DISC OUT RX audio output without de-emphasis
pin 9 AF OUT RX audio output with de-emphasis
pin 10 GND GND
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu DR-2X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu DR-2X in the language / languages: English as an attachment in your email.

The manual is 14,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info