674722
8
Zoom out
Zoom in
Previous page
1/56
Next page
DR-2X / DR-2XE Operating Manual6
Connection for DR-2XE (European and Australian versions)
Follow the outline in the illustration regarding the proper connection for the required External Power Supply.
The DC power connector for the DR-2XE must only be connected to a DC source providing 13.8V DC (±15 %),
and capable of at least 10A of current.
Always observe proper polarity when making DC connection.
Make sure to switch OFF the power of the external power source before connecting.
1 Insert the connector of the provided DC power cord into the DC IN jack at the rear of the repeater.
2 Connect the red wire (+) of the provided DC power cord to the positive (+) terminal of the external power
source, and the black wire (-) to the negative (-) terminal.
+
(red)
Fuse (15 A)
(black)
The external power source should be installed near the equipment and should be easily accessible.
Permanent damage can result when improper supply voltage, or reverse-polarity voltage, is applied to the DR-2XE.
The Limited Warranty on this radio does not cover damage caused by application of AC voltage, reverse polarity
DC, or DC voltage outside the specified range of 13.8 V ±15 %. When replacing fuses, be certain to use a fuse of
the proper rating. The DR-2XE requires a 15A blade fuse.
Connecting External Devices
Connection of an external microphone
By connecting an optional microphone MH-48A6JA or MH-42C6J to the
[
MIC
]
jack on the front panel, voice
communications are possible in the mode which is set on the transmitter. Except when AMS is set on the
transmitter, data transmission is not available via the
[
MIC
]
jack.
Connection to a personal computer
The supplied PC connection cable “SCU-20” can be used to connect the repeater to a personal computer as
a USB port.
Use the
[
ACC
]
jack to connect with the optional WIRES-X Internet Linking Kit “HRI-200”.
The pin assignments of the
[
ACC
]
jack are as follows.
PKD (packet data input)
GND
PKS (PTT)
RX 9600 (9600 bps packet data output)
RX 1200 (1200 bps packet data output)
PK SQL (squelch control)
TXD (serial data output
[
repeater PC
]
)
RXD (serial data output
[
repeater PC
]
)
CTS (data communication control)
RTS (data communication control)
z Make sure to switch off the power to the radio before connecting the cable.
z When using the SCU-20, PC connection cable, a dedicated driver must be installed in the personal computer.
Download and use the driver and installation manual from the YAESU website.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu DR-2X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu DR-2X in the language / languages: English as an attachment in your email.

The manual is 14,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info