587187
13
Zoom out
Zoom in
Previous page
1/15
Next page
22
TR600 Treadmill
TR600 Treadmill
23
Service Checklist - Diagnosis Guide
Before contacting us for aid, please review the following information. It may save you both time and expense.
This list includes common problems that may not be covered under the treadmill’s warranty.
1. Tether cord not in position.
2. Circuit breaker on front grill tripped.
Push circuit breaker in until it locks.
3. Plug is disconnected. Make sure plug is rmly pushed
into 115 VAC wall outlet.
4. Breaker panel circuit breaker may be tripped.
5. Treadmill defect. Contact XTERRA Fitness.
Display does not light
Tread-belt does not stay centered
Treadmill belt hesitates when
walked/run on
The user may be walking while favoring or putting more
weight on either the left or right foot. If this
walking pattern is natural, track the belt slightly
off-center to the side opposite from the belt
movement. See General Maintenance section on
Tread-belt Tension. Adjust as necessary.
1. If the belt moves, but stops after a short time and thedis
-
play shows “LS”, run calibration.
2. If you press Start and the belt never moves, then the
display shows LS, contact service.
Motor is not responsive after
pressing Start
Treadmill will only achieve
approximately 7 mph but shows higher
speed on display
This indicates motor should be receiving power to
operate. Low AC voltage to treadmill. Do not use an
extension cord. If an extension cord is required it should be
as short as possible and heavy duty 16 gauge minimum.
Low voltage. Contact an electrician or XTERRA Fitness. A
minimum of 110 volt AC current is required.
High belt/deck friction. See General Maintenance section
on cleaning the deck. If cleaning doesn’t prevent this from
reoccurring, check to see if there is signicant wear of the
deck. If so, the deck may need to be ipped if it is on its
original side
Tread-belt stops quickly/suddenly
when tether cord is pulled
High belt/deck friction. See General Maintenance. If
cleaning doesn’t prevent this from reoccurring, check the
amp draw of the motor. If this is high and there are signs of
signicant wear of the deck, it may need to be ipped if it is
on its original side
Treadmill trips on board 15 amp circuit
Treadmill may not be grounded. Static electricity is
“crashing” the computer. Refer to Grounding
Instructions on page 3.
Computer shuts off when console is
touched (on a cold day) while
walking/running
Need to replace the breaker with a “High In-rush
current” type breaker (see page 3 for details)
Circuit breaker trips, but not the
treadmill circuit breaker
Problem Solution/Cause
Error Messages
LS: The treadmill hasn’t received a speed signal for 8 seconds.
E1: Console memory malfunction or CPU problem.
E2: Incline position error.
If you want to set the Speed and Distance to Metric or if there is a problem with the speed
and you would like to perform the calibration procedure, use the factory settings menu. To
begin press, and hold for 5 seconds, the Start and Speed 5 keys while
installing the safety key. All the segments will light then the message window will display
software versions and tell you to press Enter.
The display will ask for grade return. This will reset the incline to zero, when set to ON,
when you stop a program.
The message window will now be showing the setting for English (miles) or Metric
(Kilometers) Use the 5/6 keys to select and press Enter
The message window will ask to adjust the wheel size for calibration. Enter 63.
The display will show a number for the lowest speed setting (for miles the number should
be 0.5). Adjust the low speed setting with the 5/6 keys and press Enter.
The display will show a number for the top speed setting (for Miles it should be 12.0).
The display will ask for top incline setting, enter 15.
Press Start to begin calibration. This is an automatic process, the belt will move and
change speeds without warning. Be Careful! When calibration is done, the console will
return to the start-up screen
Calibration Procedure
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xterra TR600 TREADMILL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xterra TR600 TREADMILL in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info