684588

Xenteq Avena 100 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Belangrijk
- Bescherm de lader voor vocht en vervuiling. Dit kan intern schade aanbrengen.
Eventuele reparatiekosten vallen niet onder de garantie.
- De lader dient tijdens het laadproces rechtop te staan.
- De acculader dient in een goed geventileerde omgeving gebruikt te worden.
- De lader kan warm aanvoelen tijdens het laadproces, dit is normaal.
Indien de AC netsnoer nog niet op de acculader aangesloten is, sluit deze dan aan op de
daarvoor bestemde aansluiting op de achterzijde van de acculader.
1. Steek de stekker van de netsnoer in een werkend stopcontact.
2. Sluit de lader aan op de accu door de stekker van de laadkabel te bevestigen op
de accuaansluiting.
3. De lader zal nu direct starten met het laadproces.
4. Als het groene lampje (OK) oplicht oftewel knippert, dan is het laadproces klaar.
De lader kan permanent aan de 230VAC netspanning aangesloten blijven zodat u, als u
de accu op wilt gaan laden, alleen de laadkabel op de accu hoeft aan te sluiten.
Als de acculader is aangesloten op de 230VAC netspanning, dan kan de acculader op
de accu aangesloten blijven tot het volgende gebruik van de accu. U hoeft de lader dus
niet na een bepaalde tijdsduur los te koppelen.
Als de lader niet is aangesloten op de 230VAC netspanning en de lader wordt langdurig
niet gebruikt, verbreek dan ook de verbinding met de accu.
LED indicaties:
Belangrijk
Beëindig het laadproces pas als het groene lampje oplicht of knippert!
Als het laadproces regelmatig voortijdig afgebroken wordt, ontstaat er blijvende
schade aan de accu.
Als de lader niet functioneert, controleer dan eerst de verbinding met de 230VAC
netspanning en met de accu. Als deze verbindingen in orde blijken te zijn en de lader
functioneert nog steeds niet, neem dan contact op met uw leverancier.
Ook als de ‘Power’ indicatie rood oplicht kunt u uw leverancier benaderen voor advies.
Power
Groen Lader aan
Rood
Foutmelding, lading onderbroken
Neem contact op met uw leverancier.
Groen
(licht op of
knippert)
Lading klaar, accu vol
Rood Laadproces in gang, accu niet vol
ok
Nederlands
ok
Important
- Protect the charger against moisture and pollution etc. This can cause damage
internally. The costs for this repair is not covered by warranty.
- The charger should stand upright during the charging process.
- The charger should be used in a well ventilated room.
- The housing of the charger can feel hot during use, this is normal.
If the AC power cord isn’t connected to the charger yet, then plug it into the appropriate
junction on the back of the charger.
1. Plug the power cord into a working electrical outlet.
2. Connect the charger to the battery by plugging the charge cable into the battery
junction
3. The charger will now immediately start charging.
4. If the green LED (OK) lights or flashes, the charging process is finished.
The charger can be left connected to the 230VAC mains continuously , so that you, if
you are going to charge the battery, only need to connect the charge cable to the
battery.
When the charger is connect to the 230VAC mains, the battery can be left connect
continuously. So you don’t need to disconnect the battery after a certain period of
time.
If the charger isn’t connected to the 230VAC mains and the charger isn’t used long
while, then also disconnected it from the battery
LED indications:
Important
End the charging process only when the green LED lights of flashes! If the
charging process is interrupted on a regular base it creates permanent damage to the
battery.
When the charger doesn’t function, always first check the wires and connections between
the charger and battery and charger and 230VAC mains. If the problem isn’t solved, then
contact your supplier. Also when the ‘power’ LED indicated red, you can contact your
supplier for advice.
Power
Green Charger on
Red
Failure, charge process stopped
Contact your supplier.
Green
(lights or flashes)
Charge process completed. Battery full.
Red Charging in process. Battery not full.
English
ok
ok
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xenteq Avena 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xenteq Avena 100 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info