Simply press ‘On’ or ‘Off’ button of RF key fob to arm or
disarm the unit.
Installation
1. Place the alarm in the desired location, using rotary wall
mount bracket provided.
2. Fix bracket to the wall using the screws supplied.
Please note that this alarm can also be used free
standing.
Operation
When exiting from the protected area
Press the ‘On’ button of RF remote control at the distance
of 10 meters, a confirmation tone will indicate that the
alarm is armed and you have 30 seconds in which to
vacate the area. After this time, if motion is detected then
the alarm will sound.
The main unit can operate with 3 Key Fob.
When entering the protected area
Simply press the ‘Off’ button of the RF remote control
within the distance of 10 meters to disarm the unit. Please
note that on entering the area, there is a short beep to
indicate that motion has been detected and a 4 second
delay before the alarm will sound to allow it to be
disarmed.
Detection range
The motion detector of the alarm unit has a 6 meter (20ft)
with approximate angles of 30º vertical and 60º horizontal.
Care and maintenance
To clean the case, simply use a soft slightly damp cloth
with water and wipe dry immediately.
Caution: Never use chemicals to clean the case, as they
may cause damage to the plastic and cause the alarm not
to function.
Troubleshooting
The unit does not sound when the batteries are
installed
Ensure that the batteries are connected correctly according
to the diagram in the battery compartment
The alarm does not arm
Ensure that the back plate of the alarm unit is secure to
hold the batteries in place and that the red light comes on
when the keypad buttons are pressed
The red light located in the middle of the alarm 4 is on
This is the low battery warning indicator light.
The batteries need replacing
Battery precautions
When using this product follow these precautions at all times.
• Use only the appropriate size batteries
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Incorrect polarity may cause damage to the alarm.
• Do not mix different types of battery such as Alkaline
and Carbon-zinc or old batteries with new.
• If the alarm is not used for long periods of time, remove
the batteries to prevent damage or injury from possible
battery leakage.
• Do not recharge batteries not intended to be recharged
as they can overheat and rupture. (Always follow the
manufacturer's directions.)
1
2
3
7
8
9
6
3
4
5
A
Controls
1. Motion Sensor
2. Alarm Speaker
3. Battery Low Indicator
4. On/Off Switch Button
5. Learning Code Button
6. Rotary Wall Mount Bracket
7. RF Keyfob
8. RF Keyfob ‘On’ Button
9. RF Keyfob ‘Off’ Button
Battery installation
Leaving the protected area
1. The battery compartment is accessed from the rear
of the alarm unit by removing the back cover.
2. Insert two (2) ‘AA’ size batteries (not included)
following the polarity A.
3. When the last battery is inserted the alarm will
beep very loudly to indicate that the batteries are
installed properly. If no beep sound, it means the
batteries are not installed properly.
4. Re-place the back cover again.
The Battery Low LED will light when the batteries is
needed to be replaced.
RF Key Fob
The key fob uses 1 piece A23S battery (included). If
the low battery indicator is ‘On’, simply remove and
replace with fresh battery.
061107
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Xena XA901 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Xena XA901 in the language / languages: English as an attachment in your email.
The manual is 0,11 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.