1. The battery compartment is accessed from the rear
of the alarm unit by removing the screws from the
side and lifting the mounting plate C.
2. Insert four (4) ‘C’ size batteries ( not included )
following the polarity C.
3. When the last battery is inserted the alarm will
beep very loudly to indicate that the batteries are
installed properly.
4. Replace the back cover and fix with screw.
The Battery Low LED will Light when the batteries
need replacing.
Remote control
The remote control uses 3 LR44
batteries ( included ). If the red
light on the remote control does
not come on when either the
‘ARM’ or ‘DISARM’ buttons are
pressed, then the batteries
need to be replaced. Diagram B
shows where the batteries are
located. Simply remove and
replace with fresh batteries.
Programming the alarm
1. To set or change the security code of the remote
control, simply set the programmable switches 12 to
the desired code and remove the batteries from the
alarm unit. Then wait at least 30 seconds for the alarm
to reset.
2. Immediately after inserting the batteries point the
Remote Control at the alarm and press the ‘ARM’
button, the Alarm LED will flash once to indicate that it
has learnt the code of the remote control.
NOTE: The alarm must be re-programmed with the
remote control each time the batteries are removed or
replaced.
Installation
1. Place the alarm in the desired
location, preferably on the
ceiling in the center of the
area needing to be protected.
2. Remove the mounting plate
and fix it to the ceiling using
the screws and rawplugs
supplied D.
3. The alarm body can then
secured using the screws at
the sides.
Troubleshooting
The unit does not sound when the batteries are
installed
Ensure that the batteries are connected correctly
according to the diagram in the battery compartment.
The alarm does not arm
Ensure that the back plate of the alarm unit is secure
to hold the batteries in place and that the red light
comes on when the ‘ARM’ or DISARM’ buttons are
pressed.
The red light on the base of the alarm unit is on
This is the “Battery Low Indicator’. The batteries need
replacing.
The red light on the remote control does not light
up when the buttons are pressed
Remove the battery cover of the remote control and
replace the batteries as per the instructions listed
above.
Battery precautions
When using this product follow these precautions at all times.
• Use only the appropriate size batteries
• Be sure to follow the correct polarity when
installing the batteries as indicated in the battery
compartment. Incorrect polarity may cause damage
to the alarm.
• Do not mix different types of battery such as
Alkaline and Carbon-zinc or old batteries with new.
• If the alarm is not used for long periods of time,
remove the batteries to prevent damage or injury
from possible battery leakage.
• Do not recharge batteries not intended to be
recharged as they can overheat and rupture.
(Always follow the manufacturer’s directions.)
Operation
When exiting from the protected area
Point the remote control at the alarm unit and press the
‘ARM’ button. A confirmation tone will indicate that the
alarm is armed and you have 30 seconds in which to
vacate the area. After this time, if motion is detected then
the alarm will sound.
When entering the protected area
Simply point the remote control at the alarm unit and
press the ‘DISARM’ button. Please note that on entering
the area, there is a short beep to indicate that motion has
been detected and a 4 second delay before the alarm will
sound to allow it to be disarmed.
Detection range
The motion detector of the alarm unit has a detection
range of 360º.
Detection Area
Care and maintenance
To clean the case, simply use a soft slightly damp cloth
with water and wipe dry immediately.
CAUTION: Never use chemicals to clean the case, as they
may cause damage to the plastic and cause the alarm not
to function.
www.xenasecurity.com
*Tested at 25˚C (range may vary
at higher temperature).
60º
061107
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Xena XA601 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Xena XA601 in the language / languages: English as an attachment in your email.
The manual is 0,17 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
