673104
10
Zoom out
Zoom in
Previous page
1/12
Next page
10
WX800 WX800.9
Lithium-Ion cordless
angle grinder
xINR18/65-y: Cylindrical lithium
Ion battery cells with max diameter
of 18mm and max height of 65mm;
“x” represents a number cells serial
connected, blank if 1; “-y” represents a
number of cells paralleled connected,
blank if 1.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE:
The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting metal, a special protection guard
for cutting (accessory) must be used.
ASSEMBLY AND OPERATION
Action Figure
BEFORE OPERATION
Removing the battery pack See Fig. A1
Charging the battery pack See Fig. A2
Installing the battery pack
WARNING: When
replacing the battery
pack, do not insert the
battery until the Grinding/
Cutting Disc comes to a
complete stop!
See Fig. A3
ASSEMBLY
Assembling Auxiliary Handle See Fig. B
Assembling Grinding/Cutting
Disc
See Fig. C1,
C2, C3
Adjusting Wheel Guard
NOTE: Before any work on
the machine itself, remove
the battery pack. For work
with grinding or cutting
discs, the protection guard
must be mounted. Use the
correct type of disc for your
application. If the power
tool is intended to perform
cutting off operations, a
guard specific for this op-
eration must be fitted.
The coded projection on the
wheel guard ensures that only a
guard that fits the machine type
can be mounted.
Open the clamping lever (13).
Place the wheel guard with
coded projection into the coded
groove on the spindle of the
machine head and rotate to
the required position (working
position).
To fasten the wheel guard, close
the clamping lever (13).
The closed side of the
wheel guard must always
point to the operator.
See Fig. D
OPERATION
Using On/Off Switch See Fig. E
Hand Grip Areas See Fig. F
Rough Grinding
WARNING! Never use a
cutting disc for
roughing.
Cutting See Fig. G
WORKING HINTS FOR YOUR
ANGLE GRINDER
1. Always start at no load to achieve maximum
speed then start working.
2. Do not force the disc to work faster, reducing the
Disc’s moving speed means longer working time.
3. Always work with a 15-30 angle between disc and
workpiece. Larger angles will cut ridges into the
workpiece and affect the surface finish. Move the
angle grinder across and back and forth over the
workpiece.
4. When using a cutting disc never change the
cutting angle otherwise you will stall the disc
and angle grinder motor or break the disc. When
cutting, only cut in the opposite direction to the
disc rotation. If you cut in the same direction as
the disc rotation the disc may push itself out of
the cut slot.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX800 in the language / languages: English as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worx WX800

Worx WX800 User Manual - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info