Manual Worx WX671.1 (page 11 of 108) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575133

Zoom out

Zoom in

1/108

High frequency multi-function tool EN

6. MOUNTING THE SUCTION DEVICE

(See Fig. C,D)

When vacuuming, mount the suction device

as shown in C1-D2.

NOTE: Using the sanding pad perforated. You

can only do the vacuuming after ﬁtting the

dust collector.

7. SANDING

Typical application: wood, metal; small areas,

especially corners, edges and places difﬁcult

to access.

Select high oscillation frequency.

Sand with a constant movement and light

pressure.

Heavy pressure does not increase the removal

– The sanding sheet merely wears faster.

8. SAWING WITH THE SEGMENT SAW

BLADE

Typical application: wood, plastics, sheet

metal.

Select high oscillation frequency.

The saw blade lasts longer if the wear

is distributed evenly. To ensure an even

distribution, loosen the saw blade, rotate it

and retighten ﬁrmly.

9. SAWING WITH THE UNIVERSAL END

CUT SAW BLADE (See Fig. E)

WARNING: The sawing teeth are

very sharp. Do not touch during

mounting and application.

The workpiece must be inserted ﬁrmly or

clamped tightly before it is cut.

Typical application: wood, metal (e. g.

nails),plaster board and soft plastics.

When plunging and sawing use a slight

pendulum motion, to allow sufﬁcient chip

removal.

10. SCRAPING

Typical application: Scraping off old varnish or

adhesives, removing glued carpeting,

e. g. on stairs or other small to medium-sized

surfaces.

Select medium/high oscillation frequency (for

variable speed models).

WORKINg HINTS FOR yOuR

TOOL

If your power tool becomes too hot, especially

when used at low speed, set the speed to

maximum and run it with no load for 2-3

minutes to cool the motor. Avoid prolonged

usage at very low speeds. Always keep the

blade sharp.

Always ensure the workpiece is ﬁrmly held or

clamped to prevent movement.

Any movement of the material may affect the

quality of the cutting or sanding ﬁnish.

Start your tool before working and turn it off

only after you stop working.

Do not start sanding without having the

sandpaper ﬁtted.

Do not allow the sandpaper to wear away , it

will damage the sanding pad. The guarantee

does not cover sanding pad wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit

for ﬁnishing surfaces. If necessary, ﬁrst make

a test run on scrap material.

Excessive force will reduce the working

efﬁciency and cause motor overload.

Replacing the accessory regularly will

maintain optimum working efﬁciency.

MAINTENANCE

Remove the plug from the socket

before carrying out any adjustment,

servicing or maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no

user serviceable parts in your power tool.

Never use water or chemical cleaners to

clean your power tool. Wipe clean with a

dry cloth. Always store your power tool in a

dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order

to avoid a hazard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX671.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX671.1 Manual

Product: