673271
10
Zoom out
Zoom in
Previous page
1/12
Next page
10
Nickel-Cadmium
Impact drill
WX369.3 WX369.4
drilling operation.
The Bubble level is recessed in the motor housing on
the back of the drill. It can be used to keep the drill
level during vertical drilling operation.
11. DRILLING
When drilling into a hard smooth surface, use a
center punch to mark the desired hole location. This
will prevent the drill bit from slipping off center as the
hole
is started. Hold the tool firmly and place the tip
of the bit at the point to be drilled. Depress the switch
trigger to start the tool. Move the drill bit into the
workpiece, applying only enough pressure to keep
the bit cutting. Do not force or apply side pressure to
elongate a hole.
Tungsten carbide drill bits should always
be used for concrete and masonry. When
drilling in metal, only use HSS drill bits in good
condition. Always use a magnetic bit holder
(not included) when using short screwdriver
bits. When screw-driving, apply a small
quantity of liquid soap or similar to the screw
threads to ease insertion.
12. DISPOSAL OF AN EXHAUSTED BATTERY
PACK
To preserve natural resources, please recycle
or dispose of the battery pack properly. This
battery pack contains NI-Cd batteries. Consult
your local waste authority for information
regarding available recycling and/or disposal options.
Discharge your battery pack by operating your drill,
then remove the battery pack from the drill housing
and cover the battery pack connections with
heavy-duty adhesive tape to prevent short circuit and
energy discharge. Do not attempt to open or remove
any of the components.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN
YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is on
top of the trigger, is positioned in the lock function.
Unlock the forward/reverse rotation control by
putting it into the required rotation position. Push the
trigger and the drill will start to rotate (See Fig. B).
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque adjusting
ring, you can find the torque-adjusting ring between
the Chuck (2) and the drill body. Position 1 is the
lowest torque (screw driving force) and position 20 is
the highest torque (screw driving force).
Position
is for drill operation. Regulate the torque
adjusting ring to a higher position to reach the best
result (See Fig.D-1 & D-2).
3. I CAN NOT FIT THE BATTERY INTO THE
BATTERY CHARGER. WHY?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot, the red LED light should turn on
when the battery is charging.
4. REASONS FOR DIFFERENT BATTERY PACK
WORKING TIME
Charging time problems, as above, and having not
used a battery pack for a prolonged time will reduce
the battery pack working time. This can be corrected
after several charge and discharge operations by
charging & working with your drill. Heavy working
conditions such as large screws into hard wood will
use up the battery pack energy faster than lighter
working conditions. Do not re-charge your battery
pack below 0
o
C and above 30
o
C as this will affect
performance.
MAINTENANCE
Your power tool requires no additional
lubrication or maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage
your power tool.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
local authorities or retailer for recycling advice..
.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX369.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX369.4 in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info