724661
28
Zoom out
Zoom in
Previous page
1/30
Next page
Air Brush Kit
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com 1800 909 909
MODEL: №. TG212 • 07/2017 • 53633 (toll free)
26
AFTER SALES SUPPORT
(toll free)
Air Brush Kit
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. TG212 07/2017 53633
Troubleshooting
Problem Possible Cause Solution
Insufficient
pressure.
Damaged braided air hose (10).
Loose air connections.
Loose cylinder body (27) cover
screws.
Replace the braided air hose (10).
Check and tighten loose
air connections.
Tighten cylinder body (27) cover screws.
Knocks while
compressor is
loading.
Defective connection rod
bearings.
Defective wrist pins and
wrist pin bearing.
Take the compressor to one of our
qualified Service Agents for review / repair.
Take the compressor to one of our
qualified Service Agents for review / repair.
Motor does
not work
Damaged power cord.
Defective electrical wiring.
No electrical power.
Power switch is defective.
Motor is too hot.
Check the regulator has not
been adjusted too low.
Pressure is at the shut off
pressure.
Take the compressor to one of our
qualified Service Agents or a qualified
technician for review / repair.
Take the compressor to one of our
qualified Service Agents for review / repair.
Plug the power cord (2) into a working
220 volt mains power socket.
Take the compressor to one of our qualified
Service Agents for review / repair.
Turn O the compressor at the mains
switch, remove the plug and Allow the
motor to cool for 15 minutes.
Adjust the regulator 3 turns in a clockwise
direction to increase pressure and depress
the air brush trigger.
Release air pressure by operating the
air brush.
Motor makes
strange noises
Loose or damaged bearings.
Loose connection rod screws.
Take the compressor to one of our qualified
Service Agents for review / repair.
Motor running but
no air pressure
Check the air intake filter (9).
If motor is operating continually
with no pressure and air intake
is clear.
Ensure the filter is not blocked or the holes
in the air filter cover are not blocked.
Take compressor to service agent
for review.
Spray pattern poor Airbrush paint outlet nozzle is
dirty or blocked.
Loose air connections.
Paint is too thick.
Replace or clean the paint outlet nozzle.
Check and tighten any loose air
connections.
Mix appropriate thinner into the paint.
Suddenly stops
working
Bad valve.
Loose or damaged bearings.
Take the compressor to one of our qualified
Service Agents for review / repair.
Plug compressor into alternate electical
power source.
For all other issues, please contact Customer Service on 1800 909 909
or email help@powertoolsupport.com
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone TG212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone TG212 in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info