523452

WOLF-Garten SDL 2500 EVO Manual

11
Zoom out
Zoom in
Previous page
1/94
Next page
11
en
Working with the garden chopper
1
Wear protective gloves and hearing protection!
z
Adopt a working position at the side of or behind the appliance.
Never stand in the area of the discharge opening.
z
Never put your hands in the feed or discharge opening.
z
Before switching on the appliance check whether there is any
chaff in the hopper.
z
If foreign bodies should enter the hopper or should the appliance
make unusual noises or vibrations, switch the appliance off im-
mediately and allow it to come to a standstill. Remove the mains
plug and carry out the following:
–
Check the appliance and tighten any loose parts.
–
Replace damaged parts.
–
Repairs to the appliance must be performed by an authorised
service centre.
What can be chopped?
z
Organic waste from the house and garden e.g. hedge and tree
cuttings, dead flowers, kitchen scraps.
What cannot be chopped?
z
Glass, metal parts, plastics, plastic bags, stones, material waste,
roots with earth, food, fish and meat waste
Switching on / off
Press the green button to switch on
(3)
z
Press the red button to switch off (4)
3
The machine has a circuit breaker to prevent switching
back on unintentionally after a power cut.
Overload protection
3
An overloading of the appliance (e.g. culminating in the
blocking of the blades) can lead to the standstill of the ap-
pliance after a few seconds. To protect the motor from da-
mage the appliance is automatically disconnected from
the mains by the overload protection.
z
Before putting into operation again wait for at least one mi-
nute before immediately pressing the reset button (2)
and then ON/OFF switch. If the motor does not start, clean
the collection hopper (see Maintenance).
Toggle switch (1)
3
The toggle switch enables freeing trapped material.
Position (a)
The blade pulls in the crushed material.
Position (b)
The blade rotates backwards and frees any trapped material.
1. Toggle switch to position (b).
2. Press green button (3) and do not release.
3
The toggle switch can only be used when the appliance
is switched off.
Special instructions for chopping
z
Chop branches, twigs and wood shortly after cutting (this chop-
ped material will become very hard once it has dried out, therefo-
re the maximum diameter which can be processed is less).
z
Remove the side shoots on severely ramified branches.
Maintenance
General
1
Remove the mains plug before any maintenance and
cleaning work!
When servicing the cutting tool ensure that it can still al-
ways run on even when the motor is switched off.
Wear protective gloves.
z
Store the appliance in a dry location out of the reach of children.
General cleaning information
1
Remove the mains plug before any maintenance and
cleaning work!
z
Handle the appliance with care and clean it regularly to prolong
its service life.
z
Keep the ventilation slits clean and dust-free.
z
Only use a warm and moist cloth to clean the appliance as well
as a soft brush.
z
Do not allow the appliance to get wet and do not spray with water.
Setting the cutting unit
3
The cutting unit is factory set and must not be set
during the first commissioning.
1. Switch on appliance.
2. Turn the adjustment knob clockwise until grinding noises are
audible and fine aluminium chips fall from the discharge chute
(worn points on the cutting plate are optimally balanced. The
chopping material is then better cut through).
Empty the collection container
1
Remove the mains plug before any maintenance and
cleaning work!
3
Note
The locking lever has the function of a safety switch and must
be in Position
(2) while operating the product. If the locking
lever should not be correctly snapped in, this and the switch
must be cleaned in the product, if required.
1. Bring the locking mechanism to position 1.
2. Pull the collection container completely out of the frame.
3. Empty the container.
4. Slide the collection container onto the frame as far as it will go.
5. Bring the locking mechanism to position 2.
C
C
C
C
D
E
E
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten SDL 2500 EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten SDL 2500 EVO in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info