523453

WOLF-Garten SDE 2800 EVO Manual

13
Zoom out
Zoom in
Previous page
1/98
Next page
13
en
Changing blades
1
Remove the mains plug before any maintenance and
cleaning work!
When servicing the cutting tool ensure that it can still al-
ways run on even when the motor is switched off.
For safety reasons, always have the blades changed by an
authorised service centre.
1. Unscrew the knob and fold the casing upwards to open .
2. In order to change the blades insert the hexagon spanner (1)
in the slot on the retaining plate and through the cover.
3. Loosen the two screws with the Allen spanner
(2) and take
out the worn blades.
4. Insert the new blades and tighten the screws.
1
Remove both the Allen and hexagon spanner after com-
pleting the change.
5. Close the casing again and tighten the knob .
Empty the collection container
1
Remove the mains plug before any maintenance and
cleaning work!
3
Note
The locking lever has the function of a safety switch and must
be in Position
(2) while operating the product. If the locking
lever should not be correctly snapped in, this and the switch
must be cleaned in the product, if required.
1. Bring the locking mechanism to position 1.
2. Pull the collection container completely out of the frame.
3. Empty the container.
4. Slide the collection container onto the frame as far as it will go.
5. Bring the locking mechanism to position 2.
Fixing problems
Warranty
The warranty rules issued by our company or the importer apply to every
country. As part of the warranty, we remedy malfunctions on your appli-
ance free of charge provided that this malfunction is caused by a material
or manufacturing defect. In the event of a warranty claim, please turn to
your dealer or the nearest branch office.
E
F
E
F
F
E
G
G
Problem Possible cause Solution
Motor does not start.
z
Not connected to voltage supply
z
Check protection
z
Faulty connection cable
z
Check the cable (electrical expert)
Motor hums but does not start
z
Top of casing not closed properly (safety shutdown de-
vice is tripped)
z
Close top of casing properly and screw, re-
move dirt if required.
z
Blade unit blocked
z
Switch off appliance, remove mains plug
and clean appliance on the inside
z
Faulty capacitor
z
Give appliance to authorised WOLF-Gar-
ten customer service centre for repair.
Motor does not start.
z
Extension cable too long or cross section too small
z
Extension cable min. 1.5 mm², max. 25 m
long. In the case of longer cable cross sec-
tion min. 2.5 mm
2
.
z
Socket too far from main connection and connecting
lead cross section too small
Reduced cutting output
z
Dull blade.
z
Changing blades
When in doubt, always seek out a WOLF Service location.
Attention: Put down the appliance and pull out the power plug before performing any checks or work on the blades.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for WOLF-Garten SDE 2800 EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of WOLF-Garten SDE 2800 EVO in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info