727483

Whynter RPD-711DWP Manual

13
Zoom out
Zoom in
Previous page
1/18
Next page
13
WATER DRAINAGE INSTRUCTIONS
2. CONTINUOUS / GRAVITY DRAIN METHOD
Water can be automatically emptied into a floor drain by attaching the 20” continuous/gravity drain hose to the con-
tinuous/gravity drain outlet. To use gravity to drain your portable dehumidifier, it must be installed on a level surface
or at least 12 inches above the ground, on a sturdy table or shelf unit. When using the function of continuous/
gravity drainage, your drain hose must be placed horizontally below the drainage hole. Avoid uneven ground and
folding the hose.
NOTE: When using continuous/gravity drainage setup, there may be some water collected in the water in the drain
bucket
1. Remove the continuous drain cover and then attach the 20” con-
tinuous/gravity drain hose. Make sure the hose is securely fastened
to prevent leakage.
2. Direct the drain hose toward a drain or other suitable drainage
outlet. Make sure that there are no distortions with the hose that may
stop the water flow. (See Fig. 7)
3. Select the desired humidity setting and fan speed on the unit for
continuous draining to start.
3. WATER PUMP METHOD
One of the key features of this dehumidifier is that it has a water pump that pushes water up or over a longer dis-
tance. Using this feature will enable your unit to run maintenance free.
NOTE: The water pump will ONLY engage when the drain bucket is full.
NOTE: The Pump Indicator Light will flash when there is a failure in the
pump operation. Please turn off the unit and unplug the power cord and
check the following points:
• Clean the pump filter - remove the drain bucket from the unit, pull down
the pump filter, and clean (See Fig. 9)
• Check the pump drain hose for kinks or obstructions
• Reinstall the pump filter and drain bucket properly. Turn on the unit. If
the error repeats, call for service
• Do not use this operation when the outdoor temperature is equal to or
less than 32°F. Otherwise, water hose may be blocked as the water will
turn to ice and cause the unit to fail. When the pump drain feature is not
being used, remove the pump drain hose from the outlet.
1. Make sure the continuous/gravity drain assembly is removed from
the continuous/gravity drain outlet and the plastic cover is installed.
2. Insert the 16 ft. pump drain hose (included) into the bottom pump
drain outlet (See Fig. 8), then lead the drain hose to a suitable drain-
age facility. Make sure that the hose is fully inserted to avoid water
leakage and no kinks which will cause the water to stop flowing.
3. Press the Pump button to activate the pump operation.
NOTE: The water pump will ONLY engage when the drain bucket is
full.
4. The water pump may make some noise when it starts to work with-
in the first 3 - 5 minutes. This is a part of the unit’s normal operation.
5. Select the desired humidity setting and fan speed on the unit.
Fig. 7
Fig. 8
Pump Drain
Outlet
Pump Drain
Hose
Pump filter
Fig. 9
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whynter RPD-711DWP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whynter RPD-711DWP in the language / languages: English as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info