641608
2
Zoom out
Zoom in
Previous page
1/8
Next page
2
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
It is important that the salt reservoir be never empty.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PROGRAMS DESCRIPTION) and should be filled when the
SALT REFILL indicator light
in the control panel is lit.
1.Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2.Position the funnel
(see figure)
and fill the salt
reservoir right up to its edge (approximately 1 kg);
it is not unusual for a little water to leak out.
3.Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, we recommend carrying out the
procedure before the washing cycle is started.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is for average (3) water hardness.
1. Switch on the appliance by pressing the
ON/OFF
button.
2. Switch off the appliance by pressing the
ON/OFF
button.
3. Hold down button
START/PAUSE
for 5 seconds, until you hear a
beep.
4. Switch on the appliance by pressing the
ON/OFF
button.
5. The current selection level number and the salt indicator light both
flash.
6. Press button
P
to select the desired hardness level
(see Water
Hardness Table).
7. Switch off the appliance by pressing the
ON/OFF
button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL
indicator light switches off.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser
A
should be filled
when the
RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser
B
by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml) reference
notch of the filling space - avoid spilling it. If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the
quantity of rinse aid used.
Switch the dishwasher on using the
ON/OFF
button.
Switch it off using the
ON/OFF
button.
Press button
START/PAUSE
three times - a beep will be heard.
Switch it on using the
ON/OFF
button.
The current selection level number and rinse aid indicator light flash.
Press button
P
to select the level of rinse aid quantity to be supplied.
Switch it off using the
ON/OFF
button
Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is for a medium level.
If you see bluish streaks on the dishes, set a low number (2-3).
If there are drops of water or limescale marks on the dishes, set a high
number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the
opening device A
.
Introduce the detergent into the dry dispenser
B only.
Place the amount of detergent for pre-
washing directly inside the tub.
1.When measuring out the detergent refer to the
(see PROGRAMS TABLE)
to add the proper
quantity. Compartment
B
comprises a level showing the maximum
quantity of liquid or powder detergent that can be added to each cycle.
2. Remove detergent residues from the edges of the dispenser and close
the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the closing
device is secured in place.
The detergent dispenser automatically opens up at the right time according to
the program.
If all-in-one detergents are used, we recommend using the
TABLET
button,
because it adjusts the program so that the best washing and drying results are
always achieved.
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 17 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
M
A
X
A
B
35
25
A
B
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool WDBC 3C24 P X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool WDBC 3C24 P X in the language / languages: English as an attachment in your email.

The manual is 6,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool WDBC 3C24 P X

Whirlpool WDBC 3C24 P X Quick start guide - Dutch - 8 pages

Whirlpool WDBC 3C24 P X Quick start guide - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info