793710
4
Zoom out
Zoom in
Previous page
1/4
Next page
TROUBLESHOOTING
The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended to check to see if the
problem can be easily resolved using the following list.
Anomalies: Possible causes / Solution:
The washing machine does not turn on
and/ or programme does not start
The plug is not inserted into the electrical outlet, or not enough to make contact.
There has been a power failure.
Lid is not properly closed.
The “Child lock function has been activated (if available).
The washing machine switched o automatically to save energy, before programme start or
after programme end. To switch on the washing machine, turn the programme selector rst to
“O/O” and then to the desired programme again.
The wash cycle does not start.
The “Start/Pause“ button has not been pressed.
The water tap is not open.
A “Start delay“ has been set.
Appliance stops during the
programme, and the
“Start/Pause“ light blinks
“Rinse hold“ option is activated (if available).
Programme has been changed - re-select desired programme and press “Start/Pause“ .
Appliance vibrates
The washing machine is not level.
The transport bracket has not been removed; before using the washing machine, the transport
bracket must be removed.
Final spin results are poor. The laundry
is still very wet. “Spin/Drain“ indicator
blinks, or the spin speed on the display
blinks, or the spin speed indicator
blinks after the end of the programme
- depending on the model
Unbalance of the laundry load during spinning prevented the spin phase to avoid damages on
the washing machine. This is why the laundry is still very wet. Reason for unbalance can be:
small laundry loads (consisting of only few quite big or absorbent items, e.g. towels), or big/
heavy laundry items.
If possible avoid small laundry loads.
“Spin“ button has been set to a low spin speed.
The machine is indicating an error code
(e.g. F-02, F-..) and/or “Service“
indicator lights up
Shut o the machine, disconnect the plug from the outlet, and wait about 1 minute before
turning it back on.
If the problem persists, call the After-sales service.
“Clean pump“ indicator lights up Waste water is not pumped out.
Clean the water lter
“Water tap closed indicator lights
up Appliance has no or insucient water supply.
“Detergent over dosage indicator
lights up (if available)
The symbol will light up at the end of the programme if you used too much detergent.
Too much foam is formed.
The detergent is not compatible with the washing machine (it must bear the wording “for
washing machines“, “for hand washing and washing machines“, or something similar).
XXXXX
Regulatory documentation, standard documentation, ordering spare parts and other product information can be
found:
By visiting our website docs .whirlpool. eu and parts - selfservice .whirlpool. com
Using QR Code
Alternatively, contact our After-Sales Service (See phone number in the warranty booklet). When contacting our
After-sales Service, please state the codes provided on your product’s identication plate.
For User Repair & Maintenance Information visit www.whirlpool.com
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model
identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool TDLRBX6252BS BE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool TDLRBX6252BS BE in the language / languages: English as an attachment in your email.

The manual is 2.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool TDLRBX6252BS BE

Whirlpool TDLRBX6252BS BE User Manual - German - 4 pages

Whirlpool TDLRBX6252BS BE User Manual - Dutch - 4 pages

Whirlpool TDLRBX6252BS BE User Manual - French - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info