576518
2
Zoom out
Zoom in
Previous page
1/2
Next page
Whirlpool is a registered trademark of Whirlpool USA
4000 107 36433
Load the laundry, close the door and add detergent as indicated
on the front page and as described in the chapter “Detergent and
Additives” in your Instructions for Use.
Turn the programme selector to the desired programme and
temperature.
The display shows the programme duration and the predefined
spin speed. The “Start/Pause” indicator blinks.
The washing machine is designed to save energy, therefore, if
you have selected a programme but do not start it within about
a quarter of an hour, it will switch off automatically.
To switch it on again, turn the programme selector toOff/O and
then to the desired programme again.
Push the button of any option desired - the indicator lights up.
If the combination programme/option or option/option is not
possible, the indicator switches off automatically.
Colours 15° button
Saves energy used for water heating while maintaining a
good wash result.
Supports colour maintenance when washing coloured laundry.
Recommendable for lightly soiled laundry without stains.
Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
Not selectable for Cotton 95 °C.
“Rapid” button
Enables quicker washing by shortening the programme duration.
Recommendable for only lightly soiled laundry.
Not selectable for Cotton 95 °C.
“Clean +” button
Choose this option if you use an in-wash additive for stain
removal (powder, for example “Vanish”) - it will optimize the
additives efficiency to get better wash performance and
stain removal.
Use with maximum load.
Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturers dosing instructions.
May prolong the programme by up to 15 minutes.
Appropriate for use of stain removers and bleaches on oxygen
basis. Chlorine or perborate bleaches must not be used!
“Prewash” button
Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
Do not use liquid detergent for the main wash when
selecting “Prewash”.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
Particularly suitable for areas with very soft water, washing
baby linen and helping people with allergies.
“Easy ironing” button
Reduces creasing by an increased water quantity and a very
gentle spin.
CONSUMPTION DATA
Power consumption: in off-mode 0.16 W / in left-on mode 0.16 W.
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
Approximate remaining
moisture content (%) ****
without “Rapid” with “Rapid”
1000 rpm
RMC C
1200 rpm
RMC B
1400 rpm
RMC B
Mixed 40 4.0 46 0.40 1:00 68 59 55
Cotton 95 8.0 85** 2.70 2:40 68 59 55
Cotton 60 8.0 64 1.50 2:20 1:45 68 59 55
Cotton 40 8.0 79 0.81 2:05 1:15 68 59 55
Synthetics 40 3.0 42 0.40 1:20 0:55 45 40 35
Delicates 30 1.5 60 0.40 0:46
Wool/Handwash 40 1.0 45 0.55 0:40
White 60 8.0 79 1.58 2:37
Light colours 40 4.0 50 0.45 1:20
Dark 30 4.0 40 0.43 1:40 1:15
Cotton *
60 8.0 53 1.15 4:00 62 53 53
Cotton *
60 4.0 38 0.76 3:15*** —625353
Cotton *
40 4.0 38 0.72 3:00*** —625353
Speed 15 30 3.0 20 0.15 0:15
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15 °C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water
supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.
Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options
or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
*** Automatic adaptation of programme duration after detection of wash load.
**** After programme end and spinning with maximum selectable spin speed, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
LOAD LAUNDRY, ADD DETERGENT AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Rinse hold” button
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
Particularly useful if you want to postpone spinning to a later
time, or if you want to drain only.
The programme stops to “Rinse hold” at the time the “Rinse
hold” indicator on the display blinks. The “Start/Pause”
indicator blinks as well.
Terminate the “Rinse hold” option :
Press the “Start/Pause” button ; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
If you do not wish to spin the clothes, turn the programme
selector to the “Drain” programme and press the “Start/
Pause” button to start draining.
“Spin” button
Every programme has a predefined spin speed; press the
button to set another spin speed.
If spin speed “0” is selected, the final spinning is cancelled
and the water is drained only. However, intermediate spin
phases remain during rinse.
With this function you can postpone your programme to
complete at a later time: press the button to select in how many
hours the programme shall be finished. Thus, it allows you to
have your laundry ready at a particular time and to profit from
more favourable energy rates during the night, for example.
Do not use liquid detergent when activating the “Cycle end”
button.
The time until the cycle end can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button to
loop through all the available times. To remove it again, keep
on pressing the button until you see the value “0:00”.
When you have selected the desired time until the cycle end,
press “Start/Pause” - the countdown will begin.
During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.).
If the modifications prolong the programme duration so that
it overruns the originally set time until the cycle end, the
programme will start immediately.
Sometimes the programme may finish before the selected
time until the cycle end has expired (e.g. for small loads).
In this case, the washing machine will tumble the laundry
regularly to keep it fresh, until the selected “Cycle end” time
has expired. During tumbling, the display will show an
animation. The tumbling phase can be stopped at any time
either by pressing any button or by rotating the programme
selector; the animation will stop and the door will unlock in
about 1 minute as indicated on the display.
The “Eco monitor” gives you a rough feedback about the power
consumption of the programme setting you selected.
As soon as you turn the programme selector to any programme,
the “Eco monitor” is on.
The indicator on the left is to show that the “Eco monitor”
is active. The four indicators next to it show the degree of
consumption: the less power your programme setting is
forecasted to consume, the less indicators will light up.
This depends on the programme, temperature and options
selected, and also on the size of the wash load. For that reason,
the forecasted degree of power consumption may adapt when
the washing machine detects the wash load.
Open the water tap and press the “Start/Pause” button .
The “Start/Pause” indicator lights up.
When the laundry load is detected or the programme duration is
updated, an animation appears on the display.
Before starting and after end of a programme, the indicator lights to
show that the door can be opened.
As long as a wash programme is running, the door remains locked
and must on no account be forced open. In case you have an urgent
need to open it during a running programme, refer to “Reset a
running programme”.
If one of the failure indicators blinks, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
“Service”: failure or malfunction of an electrical component.
“Clean pump”: waste water is not pumped out.
Spin speed blinks: unbalance during spinning.
The “Door open” indicator lights up, and the display
shows “End”. After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the “Start/Pause” button to pause the
programme. The indicator blinks.
2. Select the new programme and, if you want, another spin
speed and any options.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The “Reset” button cancels a programme before the end.
•Press and hold the “Reset” button for a few seconds.
The water is drained. It may last some time until the door
can be opened.
SET CYCLE END
ECO MONITOR
less more
PROGRAMME START
“DOOR OPEN” INDICATOR
FAILURE INDICATORS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME
- the sensor technology adapts drum movement, water, energy and programme duration to your wash load
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool Primo 1408 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool Primo 1408 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool Primo 1408

Whirlpool Primo 1408 Quick start guide - German - 2 pages

Whirlpool Primo 1408 User Manual - Dutch - 40 pages

Whirlpool Primo 1408 Quick start guide - Dutch - 2 pages

Whirlpool Primo 1408 Quick start guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info