Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
•Turn the programme selector to the desired programme and
temperature. The display shows the programme duration and
the predefined spin speed. The lamp next to the “Start/
Pause” button blinks.
Push the button of any option desired - the respective indication lights up.
If the combination of programme and option is not possible, the
indication lights switch off automatically. Unsuitable combinations
of options are deselected automatically.
“Prewash” button
•Only for heavily soiled loads (for example sand, granular dirt).
Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when selecting
“Prewash”.
“Rapid” button
•Enables quicker washing by shortening the programme duration.
•Recommendable for small loads or only lightly soiled laundry.
“Clean +” button
•Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
•Use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•May prolong the programme by up to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis. Chlorine or perborate bleaches must not be used!
“Cold wash” button
•Water is heated only up to 20°C.
•Suitable for delicate laundry items with wash temperature
recommendation of max. 30° on the care label.
•Mainly selectable on the lowest temperature step of the
programmes only.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft
water, washing baby linen and helping people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very
gentle spin.
“Rinse hold” button
•The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
CONSUMPTION DATA
ProgrammeTemperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approximate programme duration
(hrs.min)
without “Rapid”with “Rapid”
Cotton956.059***1.902:00—
Cotton*606.0490.784:002:30
Cotton*603.0370.702:30
Cotton406.0600.702:451:45
Cotton*403.0370.602:30
Jeans 405.0760.703:002:00
Synthetics603.050***0.801:351:14
Synthetics403.0460.501:200:59
Delicates301.5600.500:45—
Daily load403.0410.501:00—
Quick wash303.0410.400:30—
Wool401.0600.500:45—
Wool201.060<0.100:40—
Handwash401.0450.50
0:40—
Lingerie 301.0450.40
0:36—
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with
respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. Water and energy consumption refer
to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
*Reference programmes for Energy Label.
**Automatic adaption of programme duration after detection of wash load.
***To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
**
**
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
•Particularly useful if you want to postpone spinning to a later
time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at the time the
“Rinse hold” light in the programme sequence indication is on. The
indication lamp next to the “Start/Pause” button blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button ; the programme will terminate
automatically with the final spin cycle for the present wash programme.
•If you do not wish to spin the clothes, turn the programme
selector to the “Drain” programme and press the “Start/
Pause” button .
“Spin” button
•Every programme has a predefined spin speed; press the
button if you want to set a different spin speed.
•If spin speed “0” is selected, the final spinning is cancelled and
the water is drained out only. However, intermediate spin
peaks remain during rinse.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating “Start delay”.
•Select programme, temperature and options.
•Press the “Start delay” button to select the desired delay time
between 30 minutes and 23 hours.
•Press the “Start/Pause” button .
On the display, the start delay symbol and the dot between hours
and minutes blink. The countdown of the delay time begins.
•The delay time indication disappears when the programme
starts and it is replaced by the remaining programme duration.
•Once having pressed the “Start/Pause” button , the delay
time can be reduced by pressing again the “Start delay” button.
To cancel the “Start delay”
•Turn the programme selector to another position, or press the
“Start/Pause” button - the selected start delay
disappears from the display. Press “Start/Pause” again if
you want to start the selected programme immediately.
Open the tap and press the “Start/Pause” button . The
indication lamp next to the “Start/Pause” button lights up.
The programme sequence indicator shows the current programme
phase, running from left to right through Wash, Rinse, Drain/Spin.
Before starting and after end of a programme, the lamp lights to show
that the door can be opened. As long as a wash programme is running,
the door remains locked and must on no account be forced open. In
case you have an urgent need to open it during a running programme,
refer to “Cancel a running programme before the end”.
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component.
“Water tap closed”
The washing machine has no or insufficient water supply; the water
tap might be closed or the water inlet hose kinked.
“Clean pump”
Waste water is not pumped out. The drain hose may be kinked or
the filter must be cleaned (see “Cleaning the filter” in your
Instructions for Use).
•All the lights of the programme sequence indicator are off
and the “Door open” indication lights up.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
4.Leave the door ajar to allow the drum to dry.
1.Press the “Start/Pause” button to pause the
programme. The light blinks.
2.Select the new programme and, if you want, another spin
speed and any options.
3.Press the “Start/Pause” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The “Reset” button cancels a programme before the end.
•Press and hold the “Reset” button for a few seconds.
Any existing water is drained out. It may last some time until
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Whirlpool Hudson 1400 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Whirlpool Hudson 1400 in the language / languages: English as an attachment in your email.
The manual is 1,19 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
