539821

Whirlpool AWO 6S445 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
5019 301 06427
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
Close the door and turn the programme selector to the
desired programme and temperature. The indication lamp
next to the
“Start (Pause)”
button blinks.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Clean +” button
• Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Selectable for programmes “Cotton” and “Synthetics”; choose
temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for
stain removal (powder) to the main wash chamber,
together with your detergent (only use powder
detergent with this option). Respect the
manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15 minutes.
• Appropriate for use of stain removers and bleaches on
oxygen basis.
Chlorine or perborate bleaches must
not be used!
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, for washing baby linen and helping people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and “Delicates”.
• It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold” light in the programme sequence
indication is on. The indication lamp next to the
“Start
(Pause)”
button blinks.
• If you select “Rinse Hold”, do not leave the laundry
items to soak for too long.
Terminate the “Rinse hold” option:
• Press the
“Start (Pause)”
button; the programme
will terminate automatically with the final spin cycle for
the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain” programme
and press the
“Start (Pause)”
button.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton 95 6.0 59
**
1.90 2:00
Cotton
***
60 6.0 49 1.02 2:20
Cotton 40 6.0 57 0.70 2:20
Synthetics 60 3.0 49
**
0.80 1:55
Synthetics 40 3.0 45 0.60 1:40
Delicates 30 1.5 60 0.50 0:45
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Wool 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Eco Cotton 60 6.0 49 0.78 4:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household
conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the “Start delay”.
• Select programme, temperature and options.
• Press the “Start delay” button to select a delay time of
1, 3, 6, 9 or 12 hours.
• Press the
“Start (Pause)”
button.
The “Start delay” indication blinks and the countdown
of the delay time begins.
• When the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
•After the
“Start (Pause)”
button has been pressed,
the number of hours preselected can be reduced by
pressing again the “Start delay” button.
To cancel the “Start delay”
...before you press the “Start (Pause)” button:
• Turn the programme selector to another position or
press the
“Reset”
button.
...after having pressed the “Start (Pause)” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay indicator light goes off.
Open the tap and press the
“Start (Pause)”
button. The
indication lamp next to the
“Start (Pause)”
button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
When the programme phase is finished, the corresponding
indication goes out.
Before starting and after end of a programme, the lamp
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to “Cancel (Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use (“Removing the Filter”).
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start (Pause)”
button to pause the
programme. The light blinks.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The
“Reset”
button cancels a programme before the end.
• Press the
“Reset”
button for at least 3 seconds. Any
existing water is drained out before the door can be
opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The Sensor Technology automatically adapts Programme Time, Wa
ter and Energy consumption to the size of your wash load.
30106427GB.fm Page 2 Monday, November 8, 2010 4:26 PM
Black process 45.0° 150.0 LPI
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AWO 6S445 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWO 6S445 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWO 6S445

Whirlpool AWO 6S445 User Manual - English - 13 pages

Whirlpool AWO 6S445 Quick start guide - German - 2 pages

Whirlpool AWO 6S445 User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info