Manual Whirlpool AWM 8712 (page 2 of 2) (English)

521506

Zoom out

Zoom in

1/2

5019 301 06297

Whirlpool is a registered trademark of Whirlpool USA

Load your laundry, close the door properly and add

detergent as indicated on the front page and as described

in the chapter “Detergent and Additives” in your

Instructions for Use (remove separator in detergent

dispenser for use of powder detergent if necessary).

1. Turn the

programme selector

to the desired

programme. The display shows the programme duration

in hours and minutes as well as the predefined

temperature. The

“Start (Pause)”

button blinks.

2. The

temperature

can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined

spin speed

lights up; in case you want to set another spin speed,

press the “Variable spin” button .

Push the button(s) of any option(s) desired - the respective

indication lights up.

When the combination of programme and option is not

possible, the lights switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Eco” button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

“Easy ironing” button

• Helps to make ironing easier.

• Increases the water quantity and the clothes are spun

very gently.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water, washing baby linen and helping people with allergies.

“Variable spin” button (incl. “Rinse hold” )

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If you select spin speed “0”, the final spinning is

cancelled but intermediate spin peaks remain during

rinse. The water is drained out only.

•If you select

“Rinse hold”

, the laundry remains in

the last rinse water without progressing to the final spin

cycle to avoid creasing and prevent colours from changing.

-Select

“Rinse hold”

if you want to postpone

spinning to a later time or if you want to drain only.

- Do not leave the laundry to soak in the rinse hold for too long.

- The programme stops to “Rinse hold” when the “Rinse

hold” light in the programme sequence indicator

is on; the

“Start (Pause)”

button

light blinks.

-To terminate the “Rinse hold” by draining the

water, without any spinning, press the

“Start

(Pause)”

button

- To terminate the programme by spinning the

laundry, press the “Variable spin” button to select

the desired spin speed and then the

“Start

(Pause)”

button to start the spin cycle.

CONSUMPTION DATA

Programme

Te mpe ra t ur e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

White Cotton / Antibacterial 95 7.0 74

2.10 2:10

Cotton / Coloured 60 7.0 69 1.33 2:10

Cotton / Coloured with “Eco”

***

60 7.0 54 1.19 2:20

Cotton / Coloured 40 7.0 69 0.75 2:05

Synthetics 60 3.5 46

0.85 1:35

Synthetics 40 3.5 42 0.50 1:20

Delicates 30 2.5 60 0.40 0:45

Wool 40 2.0 60 0.60 0:45

Handwash 40 2.0 45 0.60 0:40

Jeans 40 7.0 86 0.75 2:21

Big Items 40 3.0 74 0.75 1:30

Sport 30 3.5 54 0.55 1:34

SuperEco 60 7.0 69 0.84 4:00

Daily load 40 6.0 73 0.60 1:00

Speed 15 30 3.0 30 0.20 0:15

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary

with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent).

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent when

activating the “Start delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select a delay time up to 23

hours; the light of the

“Start (Pause)”

button blinks.

•Press the

“Start (Pause)”

button ; the countdown

of the delay time begins. The light of the

“Start

(Pause)”

button is on; the light of the start delay

button will keep blinking until the programme starts.

• As soon as the programme starts, the start delay on

the display is replaced by the remaining programme

time, and the light of the “Start delay” button goes off.

• Once having pressed the

“Start (Pause)”

button ,

the number of hours preselected can be changed by

pressing and holding the “Start delay” button.

To cancel the “Start delay”

...before you press “Start (Pause)” :

• Turn the programme selector to another position or

press the

“Reset/Drain”

button .

...after having pressed “Start (Pause)” :

• Press

“Start (Pause)”

- the delay time disappears

from the display; press

“Start (Pause)”

again to

start the selected programme immediately.

Open the tap and press

“Start (Pause)”

; the light

stops blinking and is on. The programme sequence

indicator shows the current programme phase, running

from left to right through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is

the case,

an animation appears on the display

Activating the child lock prevents children from starting a

wash cycle or changing the settings of a running

programme. The child lock cannot be activated or

deactivated when the programme selector is in the “Off/

O” position. To activate the child lock:

• Turn the programme selector to a programme

position, or run a programme as usual.

• Press the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds; a key-like

symbol will shortly appear on the display to indicate

that the child lock is active.

Any time you try to change a programme setting with

active child lock, the display will shortly show the key-like

symbol. The programme setting cannot be changed

anymore; the only change possible is to switch the washer

off by turning the programme selector to the “Off/O”

position. To deactivate the child lock:

• Press again the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds.

Before starting and after end of a programme, the lamp

lights to show that the door can be opened. As long as a

wash programme is running, the door remains locked and

must on no account be forced open. In case you have an

urgent need to open it during a running programme, refer

to “Reset a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by a

fault in an electrical component. Refer to the

“Troubleshooting Guide” in your Instructions for Use; if

the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the

water tap; if the indication still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain

hose is kinked or the filter must be cleaned; in the latter case

refer to the Instructions for Use (“Removing the Filter”).

• The display shows “End” and the “Door open”

indication lights.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press

“Start (Pause)”

to pause the programme;

the light blinks.

2. Select the new programme, temperature, any options

and another spin speed if you want.

3. Press

“Start (Pause)”

again. The light is on, and

the programme continues at the same position where

the previous programme was interrupted. Do not add

detergent for this programme.

The

“Reset/Drain”

button cancels a programme

before the end.

• Press the

“Reset/Drain”

button for at least 3

seconds; “rES” appears on the display. Any existing

water is drained before the door can be opened.

START DELAY

PROGRAMME START

CHILD LOCK

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

30106297GB.fm Page 2 Wednesday, June 10, 2009 3:48 PM

Black process 45.0° 150.0 LPI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AWM 8712 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AWM 8712

Whirlpool AWM 8712 Quick start guide - German - 2 pages

Whirlpool AWM 8712 User Manual - German - 14 pages

Whirlpool AWM 8712 User Manual - Dutch - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Whirlpool AWM 8712 Manual

Product: