314433

Whirlpool awg 912 d Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
5019 301 20135
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in the Instructions for Use.
1. Turn the
programme selector
to the desired
programme.
2. The indicator of the predefined
spin speed
lights up; in case you want to set another spin
speed, press the “Variable spin” button.
Press the button(s) of any required option(s) - the
respective indicator lights up.
When the combination of programme and
additional option(s) is not possible,
the indicators switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Prewash” button
• Only for heavily soiled loads (e.g. sand, granular dirt).
Increases the cycle time by approx. 15 minutes.
• Do not use liquid detergent for the main wash
when activating the prewash option.
“Intensive rinse” button
• More water is added and the rinse cycle is
prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen, and helps
people with allergies.
“Easy Ironing” button
• Can be used together with “Cotton”, “Synthetic”
and “Daily load” programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
“Rinse hold” button
• The laundry remains in the last rinse water
without the final spin cycle, to avoid creasing and
prevent colours from changing.
• This option is particularly recommended for the
“Synthetics”, “Daily load” or “Delicates”
programmes.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
• If you select “Rinse hold”, do not leave the
laundry to soak for too long.
Note:
The programme stops to “Rinse hold” at
the time the “Rinse Hold” light in the programme
sequence indicator is on. The indicator next to
the
“Start”
button flashes.
To terminate the “Rinse hold” option:
•Press the
“Start”
button; the programme will
terminate automatically with the final spin cycle
for the preset wash programme.
“Variable spin” button
• Every programme has a predefined maximum
spin speed.
• Press the button to set another spin speed.
• If spin speed “00” is selected, the final spin is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
CONSUMPTION DATA
Programme
Te m p e r a t u r e
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. programme duration
(hours : minutes)
*
White Cotton / Antibacterial 90 5.0 52
**
1.70 2:10
Cotton 75 5.0 52 1.33 2:05
Cotton with “Eco”
***
60 5.0 49 0.95 2:15
Cotton 40 5.0 62 0.51 2:00
Synthetics 60 2.5 46
**
0.80 1:40
Synthetics 40 2.5 46 0.46 1:35
Daily load 40 3.5 52 0.30 1:25
Quick wash 35 2.5 30 0.40 0:40
Delicates 30 2.5 54 0.24 0:45
Wool 40 1.0 56 0.44 0:54
Handwash 30 2.0 65 0.24 0:57
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. In domestic use, consumption
data may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display (if present) can deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference programme for energy label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
The “Start Delay” option allows you to programme
machine activation at a later stage, for example at
night when electricity is cheaper. Do not use liquid
detergent when activating the “Start delay”.
• Select the programme and options.
• Press the “Start Delay” button to select
programme start a delay time of 1 to 16 hours;
•Press the
“Start”
button.
The indicator next to the
“Start delay”
button
lights up, whereas the selection made is shown
on the display.
Its flashing indicates the countdown of the
remaining time.
• At the end of the delay time the machine starts
the set programme. The icon indicating the wash
cycle step being carried out at that moment is
displayed.
• After pressing the
“Start”
, the number of hours
preselected can be reduced by pressing and
holding the “Start Delay” button.
To cancel the “Start Delay”:
Press the
“Start delay”
button until the time
indicated on the display is “00”; the selected
programme will then start.
Open the tap and press the
“Start”
. The indicator
next to the
“Start”
button lights up.
At the end of a programme, the message “End”
appears on the display, indicating that the door can
be opened. As long as a wash programme is running,
the door remains locked and must not be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
E02-E03 “Service”
The display of this “Service” code can be due to a
faulty electrical component. Refer to the
“Troubleshooting guide” in the Instructions for Use;
If the fault persists, contact the After-Sales Service.
E01 “Pump cleaning”
The water is not discharged. Check if the drain hose
is bent or if the filter requires cleaning; in the latter
case, refer to the Instructions for Use (“Removing
the filter”).
E00 “Water tap closed”
The washing machine water feed is insufficient or
lacking. Open the tap; Turn the programme
selector to “Off/O” and reset the programme. If the
fault remains displayed, consult the
“Troubleshooting guide” in the Instructions for Use.
E04 “Door lock”
The display of this code could be due to the door
not being properly closed. Try closing it again. Turn
the programme selector to “Off/O” and reset the
programme. If the fault remains displayed, consult
the “Troubleshooting guide” in the Instructions for
Use.
• At the end of the wash cycle, the message
“END” will appear on the display, indicating
that the door is unlocked.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and remove the washing.
4. Leave the door ajar to allow the drum to dry.
1. Turn the programme selector to “Off/O”.
2. Select the new programme, any options and
another spin speed if you want.
3. Press the
“Start”
button again. The new
programme resumes the wash programme
from where the previous one was interrupted.
Do not add detergent for this programme.
• Reset by turning the programme selector to
“Off/O” and select the “Drain Spin”
programme to remove the water remaining in
the bowl before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATOR
DISPLAY ALPHANUMERIC INDICATIONS
END OF WASH CYCLE
CHANGING PROGRAMME AND/OR
OPTIONS AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30120135GB.fm Page 2 Tuesday, September 18, 2007 9:47 AM
Black process 45.0° 150.0 LPI
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool awg 912 d at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool awg 912 d in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool awg 912 d

Whirlpool awg 912 d User Manual - English - 14 pages

Whirlpool awg 912 d Quick start guide - French - 2 pages

Whirlpool awg 912 d User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info