450397
2
Zoom out
Zoom in
Previous page
1/2
Next page
5019 301 06374
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
1. Turn the
programme selector
to the desired programme
and temperature.
2. The
time display
shows the duration of the chosen
programme (in hours and minutes), and the
“Start (Pause)”
indication lamp
blinks.
3. The indication lamp of the predefined
spin speed
lights up.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Clean+” button
Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
Selectable for programmes “Cotton” and “Synthetics”; choose
temperature of 30 or 40°C and use with maximum load.
Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
Prolongs the programme by approx. 10 to 15 minutes.
Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Prewash” button
Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Easy ironing” button
Can be used together with “Cotton, “Synthetics” and “Daily
load” programmes to make ironing easier.
Increases the water quantity and the clothes are spun very gently.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Rinse hold” button
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
This option is particularly recommended for the programmes
“Synthetics”, “Daily load” and “Delicates”.
It is particularly useful if you want to postpone spinning to a
later time, or if you want to drain only.
If you select “Rinse hold” do not leave the laundry items to
soak for too long.
Note:
The programme stops to “Rinse hold” at the time the
“Rinse hold” light in the programme sequence indication is on.
The indication lamp next to the
“Start (Pause)”
button blinks.
Terminate the “Rinse hold” option:
Press the
“Start (Pause)”
button; the programme will
terminate automatically with the final spin cycle for the present
wash programme.
CONSUMPTION DATA
Programme
Te m p e r a t u re
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton 95 6.0 59
**
1.90 2:00
Coloured Cotton
60 6.0 49 1.02 2:20
Coloured Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Wool 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Eco Cotton
***
60 6.0 49 0.78 4:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary
with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
If you do not wish to spin the clothes, turn the programme
selector to the “Drainprogramme and press the
“Start
(Pause)”
button.
“Spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
Select programme, temperature and options.
Press the “Start delay” button to select the delay time by 1 to 23 hours.
•Press the
“Start (Pause)”
button.
The countdown of the delay time begins; the “Start delay”
indication lamp and the dot on the display will keep blinking
until the programme starts.
The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
Once having pressed the
“Start (Pause)”
button, the number
of hours preselected can be reduced by pressing again the
“Start delay” button.
To cancel the “Start delay”
...before you press the “Start (Pause)” button:
Turn the programme selector to another position or press the
“Reset”
button.
...after having pressed the “Start (Pause)” button:
•Press the
“Reset
button for at least 3 seconds - the start
delay time disappears from the time display.
Open the tap and press the
“Start (Pause)”
button. The
indication lamp of the
“Start (Pause)”
button lights up. The
programme sequence indicator shows the current programme
phase, running from left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case, an animation appears on the time display.
Before starting and after end of a programme, the lamp lights to
show that the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Guide” in your
Instructions for Use; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water
tap; if the indication still lights up, refer to the “Troubleshooting
Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned; in the latter case refer to the
Instructions for Use (“Removing the Filter”).
All the lights of the programme sequence indicator are off,
and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start (Pause)”
button to pause the programme.
The light blinks.
2. Select the new programme (with temperature), any options
and another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset”
button cancels a programme before the end.
•Press the
“Reset
button for at least 3 seconds; “rES”
appears on the display. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106374GB.fm Page 2 Wednesday, April 14, 2010 6:29 PM
Black process 45.0° 150.0 LPI
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool Atlanta 1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool Atlanta 1600 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool Atlanta 1600

Whirlpool Atlanta 1600 User Manual - English - 14 pages

Whirlpool Atlanta 1600 User Manual - English - 8 pages

Whirlpool Atlanta 1600 Specifications - German - 2 pages

Whirlpool Atlanta 1600 User Manual - German - 14 pages

Whirlpool Atlanta 1600 User Manual - German - 8 pages

Whirlpool Atlanta 1600 Specifications - Dutch - 2 pages

Whirlpool Atlanta 1600 User Manual - Dutch - 8 pages

Whirlpool Atlanta 1600 Specifications - French - 2 pages

Whirlpool Atlanta 1600 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info