Manual Whirlpool AKT 320 (page 2 of 2) (English)

662517

Zoom out

Zoom in

1/2

TROUBLESHOOTING GUIDE

The steak plate does not work:

- Check for the presence of mains electrical power.

- Set the knob to

“0”

and switch on the hob again to

ensure that the fault has been remedied.

The steak plate does not turn off:

- disconnect the hob immediately by disconnecting the

power cable from the socket.

ACCESSORIES:

• The glass cover can be ordered via the After Sales

Service, with the code: AMC 966 NB (New Black)

AMC 966 MR (Mirror).

AFTER-SALES SERVICE

Before contacting After-Sales Service:

• See if you can solve the problem yourself with the help

of the suggestions given in chapter “Troubleshooting

Guide”.

If after the above checks the fault persists, contact the

nearest After-sales Service.

Please give:

• a brief description of the fault;

• the type and exact model of the hob;

• the service number (i.e., the number that follows the

word SERVICE on the rating plate, located under the

hob). The service number is also indicated on the

warranty booklet;

• your full address;

• your telephone number and area code.

If any repairs are required, please contact an

authorised

After-sales Service

(to guarantee that original spare parts

will be used and repairs carried out correctly).

Failure to comply with these instructions may

compromise the safety and quality of the product.

INSTALLATION

Recommendations

Important: Before any installation or maintenance

operation, disconnect the steak plate from the mains

power supply.

• Electrical connections must be made before connecting

the appliance to the electricity supply.

• Installation must be performed by a qualified technician

according to the manufacturer's instructions and current

local regulations.

• After unpacking the steak plate, check that there has

been no damage during transport.

If in doubt, contact

the nearest dealer or Authorised After Sales

Service.

Preparation of fitted cabinet

• Perform all required cuts on the work top before

inserting the appliance. Carefully remove all chips or

residue which could impair efficient operation of the

appliance.

• The hob must be recessed in a work top with a

thickness of min. 30 and max. 50 mm.

• Insert a separator panel at a minimum distance of

20 mm from the bottom of the steak plate, so that it is

not accessible to the user.

• If the hob is to be fitted above an oven, the latter must

be produced by the same manufacturer and equipped

with a cooling system.

• Never place other materials between the steak plate

and oven (e.g. cross-members, insulation, etc.).

• If the steak plate is to be installed next to a column unit,

leave a distance of at least 100 mm from the steak plate

edge.

• Make an opening in the worktop, observing the

dimensions specified.

• Fit the seal supplied onto the hob (if not already

present), after carefully cleaning the application surface.

ASSEMBLY:

After having cleaned the perimeter surface, apply the

supplied gasket to the hob as shown in the figure.

Important:

before installing the steak plate, remove any

plastic protection film applied.

Ensure that the opening made in the worktop to house the

steak plate corresponds to the dimensional drawing

specifications, within the relative tolerances.

Never force the steak plate into the worktop.

•

For installation

, use the relative brackets and screws

supplied.

Position the hob in the work top opening made respecting

the dimension indicated on first page.

NOTE:

The power supply cable must be long enough to

permit its upward extraction.

To secure the hob, use the brackets

(A)

provided with it.

Fit the brackets into the relevant bores shown by the

arrow and fasten them by means of their screws in

accordance with the tickness of the work top (see fig. 1).

Electrical connection

• Regulations require that the appliance is earthed.

• The electrical connection must be made by a qualified

technician according to the manufacturer's instructions

and current local regulations.

• The installer is responsible for the correct electrical

connection of the appliance and the observance of the

relative safety standards.

• To comply with directives governing safety, during

installation use a single-pole switch with a minimum gap

between contacts of 3 mm.

• Do not use multiple plug adapters or extension leads.

• After installation, electrical parts must not be accessible.

Connection to the electrical mains

Note:

the yellow/green earthing wire

(B)

must be

connected to the screw. If the power cable is not yet

connected:

• strip approx. 70 mm of sheath from the power supply

cable

• strip approx. 10 mm of sheath from the wires

• open the terminal board

(C)

by pressing the side tabs

by means of a suitable tool.

• insert the power cable

(D)

in clamp

(E)

and connect

the wires to the terminal board.

• close the terminal board cover.

• after the electrical connection, insert the hob from the

above and secure on the fixing brackets as shown in

figure 1.

Declaration of conformity

• This cooktop is suitable for contact with foodstuffs and

complies with EEC (CE) Regulation n. 1935/2004.

• This cooking hob has been designed to be used only for

cooking Any other use (such as heating a room) is

improper and dangerous

• This cooking hob has been designed, constructed and

marketed in compliance with:

- safety objectives of the “Low Voltage” Directive

2006/95/CE (which replaces 73/23/CEE and

subsequent amendments).;

- protection requirements of EEC Directive “EMC”

89/336;

- requirements of EEC Directive 93/68.

Fig. 1

Fig. 2

Fig. 3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AKT 320 in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Whirlpool AKT 320 Manual

Product: