662535
2
Zoom out
Zoom in
Previous page
1/2
Next page
BEFORE USING THE COOKING HOB
Before use, remove:
- adhesives stuck on the hob;
- cardboard guards and protective plastic film;
- check whether the hob has been damaged during
transport. If in doubt, contact the After Sales Service.
Care and maintenance
Clean the hob, when it is cool, after each use. This will
prevent the build-up of dirt and make cleaning easier.
Use a clean cloth, absorbent kitchen wipes and washing
up liquid or a specific glass ceramic cleaner.
Remove baked-on dirt with the special scraper tool
(if provided) and specific cleaning products.
Any food spills should be cleaned off before they dry.
Do not use abrasive products, chlorine-based cleaners,
oven-cleaner spray or pan scourers.
The hob should be treated periodically with specific
products available from the shops, following the
manufacturer’s instructions.
TROUBLESHOOTING GUIDE
The hob does not work:
- Make sure that the power supply is on.
- Turn the hob off and on again, to make sure that the
problem has been solved.
- Make sure that the knob is not turned to “0”.
Turn the multi-pole switch to “Off for a few minutes
and then turn it back to “On”.
The hob will not switch off:
- disconnect the hob immediately from the power
supply.
AFTER SALES SERVICE
Before you call the After Sales Service
Make sure that you cannot solve the problem yourself
following the points described in chapter
“Troubleshooting Guide”.
If after the above checks the fault still occurs, get in touch
with the nearest After Sales Service.
Please give:
a short description of the fault;
the exact type and model of hob;
service number (i.e., the number that follows the word
SERVICE on the rating plate under the hob itself);
•your full address;
your telephone number.
If any repairs are required, please contact an authorised After
Sales Service (to guarantee that original spare parts will be
used and repairs carried out correctly).
Failure to comply with these instructions may compromise
the safety and quality of the product.
INSTALLATION
Recommendations
Important: Disconnect the hob from the mains before
carrying out any installation work or servicing.
All electrical connections must be made before
connecting the appliance to the power supply.
Installation must be carried out by a qualified technician
in accordance with the manufacturer’s instructions and
in compliance with local regulations.
Unpack the hob and make sure that the appliance has
not been damaged during transport. If you are not sure
contact the dealer or the nearest service centre.
Preparing the housing unit
Cut the worktop to fit before installing the appliance.
Carefully remove any shavings or sawdust that could
prevent the appliance from running properly.
Attention: to install the hob on other surfaces than wood
(marble, plastic, ceramic, marble, stone, etc.) remember to
ask After Sales Service for the fixing plates (fig. 2)
Code 4819 404 78697.
The hob must be fitted in a worktop with a minimum
thickness of 20 mm and a maximum of 50 mm.
Insert a separator panel at a minimum distance of
20 mm from the bottom of the hob, so that it cannot be
accessed by the user.
If there is an oven under the hob, make sure that it is
manufactured by us and equipped with a cooling
system.
There must be nothing between the hob and the oven
(e.g. cables, insulating material, etc.).
An adjacent column unit must be installed at least
100 mm from the edge of the hob.
Cut an opening in the worktop of the given dimensions.
We recommend you seal the internal edges of the
worktop with wood glue or silicone.
If not already in place, apply the supplied seal to the
hob, after cleaning the adhesive surface thoroughly.
Glass-ceramic hob
Important: remove any protective film before installing the
hob.
Make sure that that the opening in the worktop for the hob is
cut according to the dimensions given in the drawing, paying
attention to the tolerance range.
The hob should not be forced into the worktop. Forcing the
glass-ceramic top may cause it to crack (even at a later date)!
If the worktop is made of wood, use the spring clips and
screws provided.
1. Secure the spring clips (A) (fig. 1) with the screws
provided (B) (fig. 1) as shown, paying attention to the
specified distances.
2. Fit the hob into the worktop.
If the worktop is made of marble, plastic, ceramic,
stone, etc., the hob must be secured with special
brackets (C) (fig. 2).
1. Fit the hob into the worktop (fig. 1).
2. Place the 4 brackets (C) in position in accordance with the
thickness of the worktop as shown in fig. 2.
3. Fasten the 4 screws (D) in the positions (E) (fig. 2).
Connecting the hob to the power supply
The installer is responsible for connecting appliances correctly
to the mains and for observing the safety regulations.
Note: the yellow/green earth wire must be connected to the
screw with the symbol .
Strip approx. 70 mm of the cable sheath from the
power supply cable (G).
Strip approx. 10 mm of sheath from the conductors.
Insert the cable (G) through the opening in the lid (F).
Insert the cable into the cable clamp and connect the
conductors to the terminal block as indicated in the
diagram printed on the lid.
Secure the power cable
(G)
by means of the cable clamp.
Refit the protection lid (F).
After the electrical connection, fit the hob from the top
and hook it to the fixing springs, according to the
illustration.
Declaration of conformity
This cooktop has been designed, constructed and
marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/CE (which replaces 73/23/CEE and
subsequent amendments).
- the protection requirements of Directive “EMC
2004/108/CE.
This cooktop is suitable for contact with foodstuffs and
complies with EEC (CE) Regulation n. 1935/2004.
PROTECTING THE ENVIRONMENT
Disposal of packaging materials
The packing material can all be fully recycled, as
confirmed by the recycling symbol .
The various parts of the packing must not be sent for
waste, but recycled in conformity with the regulations
imposed by local authorities.
Disposal of used household appliances
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or on the documents
accompanying the product, indicates that this appliance
may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the
recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more
detailed information about treatment, recovery and
recycling of this product, please contact your local city
office, your household waste disposal service or the
shop where you purchased the product.
Energy saving
Use pots and pans whose bottom diameter is equal to
that of the cooker plates, or slightly larger.
Only use flat-bottomed pots and pans.
If possible, keep the pot covered when cooking.
Cook vegetables, potatoes, etc. with little water in
order to cut down cooking time.
A pressure cooker allows you to save even more energy
and time.
Fig. 1
Fig. 2
Fig. 3
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Whirlpool AKM 9010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Whirlpool AKM 9010 in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Whirlpool AKM 9010

Whirlpool AKM 9010 User Manual - German - 2 pages

Whirlpool AKM 9010 User Manual - Dutch - 2 pages

Whirlpool AKM 9010 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info